DoorKing 6050-080 Скачать руководство пользователя | Manualshive

Страница: 12 / 42

background image

6050-065-C-2-16

8

SECTION 1 - INSTALLATION

1.1 Operator Position

35”

90°

Note: 2” thick gate Illustrated.

Gate
Bracket

An imaginary straight line drawn

from the closed gate bracket

through the open gate bracket

MUST

intersect the

operator output shaft.

For pad or post mount with

the gate opening 90°.

See 1.10 for gate’s opening wider than 90°.

Minimum distance

required for arm

clearance in the

open position.

Note: The operator can be placed further away from the open gate than
shown as long as the imaginary straight line drawn from the closed gate
bracket through the open gate bracket intersects the operator output shaft.

34”

12”

43”

Closed Gate

Open Gate

Operator

Output Shaft

Prior to beginning the installation of the swing gate operator, we suggest that you become familiar with the
instructions, illustrations, and wiring guide-lines in this manual. This will help insure that your installation is
performed in an efficient and professional manner compliant with UL 325 safety and ASTM F2200 construction
standards.

The proper installation of the vehicular swing gate operator is an extremely important and integral part of the
overall access control system.

Check all local building ordinances and building codes prior to installing this

operator. Be sure your installation is in compliance with local codes.

«
...
10
11
12
13
14
...
»

Содержание 6050-080











































Отзывы:

Нет отзывов

Похожие инструкции для 6050-080

Бренд: FAAC Страницы: 29

Бренд: FAAC Страницы: 28

Бренд: Tecno Automazione Страницы: 9

Бренд: International Door Closers Страницы: 2

Delma POLARIS 4

Бренд: Bame Страницы: 24

Бренд: CAME Страницы: 20

Бренд: Tailwind Страницы: 18

Бренд: Viking Страницы: 49

Бренд: BFT Страницы: 120

Бренд: Devanco Страницы: 42

Бренд: MAG Страницы: 9

Бренд: Parkside Страницы: 16

Бренд: GDS Страницы: 13

Бренд: FlexiForce Страницы: 16

Бренд: quiko Страницы: 8

Rotello QK-R300

Бренд: quiko Страницы: 18

SPIDER QK-S400BKIT

Бренд: quiko Страницы: 22

SCARABEO QK-SCA230

Бренд: quiko Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды