background image

 6050-065-C-2-16

34

6.3 Accessory Items

UL 325 Monitored Entrapment Protection Devices available for the model 6050 and 6100 swing gate operators.

Type B2 Contact Sensors (Photo Cell)

 

  Miller Edge Sensing Edges - all models with a T2 (resistive) termination. 
  Miller Edge Monitored Gate Link Model MGL-K20 

Type B1 Non-contact Sensors (Reversing Edge)

 

  Miller Edge Reflective-Guard Model RG 
  Miller Edge Prime-Guard Model PG 
  EMX Industries Model IRB-MON 
  EMX Industries Model IRB-RET 
  Omron Model E3K-R10K4 
  Seco-Larm Model E-931-S45RRGQ 
  Seco-Larm Model E-931-S50RRGQ 
  Seco-Larm Model E-931-S33RRGQ 
  Seco-Larm Model E-960-D90GQ 

Type B1 Non-contact Sensors (Photo Cell) requires DK P/N 9200-190 Resistor kit

 

  MMTC Model IR55 
  MMTC Model 60-278 
  Carlo Gavazzi Model PMP12 
  Carlo Gavazzi Model 8080-031 

Monitored Expansion Kit 

  Miller Edge Multi-Input Module Model MIM-62

Accessory items available for the model 6050 and 6100 swing gate operators.

Reversing Edge

 - Contact sensors for use as a safety device. Miller Edge, Inc., MGO20, MGR20, MGS20

Photo Cell

 - Non-contact sensors for use as a safety device. 

  MMTC, Inc. Model IR55    

P/N 8080-010 

  MMTC, Inc. Model 60-278   

P/N 8080-011

  Carlo Gavazzi Type PMP12   

P/N 8080-030

  Carlo Gavazzi Type PMT    

P/N 8080-031

Loop Detector

 - Detectors plug directly into ports on circuit board simplifying wiring.

  P/N 9410-010 - Single channel detector
  P/N 9409-010 - Two channel detector
  P/N 9411-010 - Single channel detector with auxiliary relay

Magnetic Lock

 - Magnetic Gate Lock Kit provides an excellent means to secure swing gates and is a fail-safe device allowing emergency 

vehicle access upon power outage. P/N 1216-080 and P/N 1216-081

3-Button Control Station

 - Three button interior and exterior control stations provide manual open-close-stop gate operation.

  P/N 1200-006 (Exterior) and 1200-007 (Interior, mounts into single-gang electrical box)

115 VAC Heater with Fan Assembly Kit

 - Thermostatically controlled heater and fan for cold and hot environments.

For 115 VAC input power ONLY. P/N 1601-154

Interconnection Cable

 - Interconnect wire cable contains all the necessary wires to interconnect primary / secondary operators. 

  Cable length 30 feet. P/N 2600-755
  Cable length 40 feet. P/N 2600-756
  Cable length 50 feet. P/N 2600-757

High Voltage Kit

 - Alter the input AC voltage on a 115 VAC 6500 to 208, 230, 460 or 575 VAC. P/N 2600-266

Time Clock

 - 7 day and 365 day time clocks can be used to automatically open gate at pre-set time and days.

Compact clock fits inside the operator.  P/N 2600-791 - 7 day clock     P/N 2600-795 - 365 day clock

Uphill Arm Pivot Assembly

 - Ball joint pivot gate connection used on uphill or downhill opening swing gates. P/N 6500-490

Torsion Rods

 - Torsion rod assembly is used on uphill swing gates for counter balance.

 P/N 

1203-084

Hinges

 - Heavy-duty ball bearing hinges provide easy swing gate operation.

  P/N 1200-009, P/N 1200-019, P/N 1200-039.

Surge Devices

 - High and low voltage surge suppressors help prevent circuit board failure caused by lightning strikes and power surges. 

  P/N 1876-010 - High Voltage
  P/N 1878-010 - Low Voltage

Molly D Grease

 - Molybdenum Disulfide (Moly D) multi-purpose grease for worm gear. P/N 2600-770 - 14 oz. tube.

Speed Bumps

 - Prefabricated six-foot speed bump reduces traffic speed through gate system. P/N 1610-150

Содержание 6050-080











































Отзывы: