background image

 6050-065-C-2-16

1

8

3.1 4502 Circuit Board Description and Adjustments

SECTION 3 - ADJUSTMENTS 

The switch settings and adjustments in this chapter should be made after your installation and wiring to the operator(s) is 
complete. 

Whenever any of the programming switches on the circuit board are changed, power must be shut-off, and then 

turned back on for the new setting to take effect.

POWER

4502-010

SAFETY

LOOP

EXIT

LOOP

1

2

KEY SWITCH

DATA

9

10

11

12

13

14

15

ON

12345678

ON

12345678

NC

NO

How LEDs Work:

 Power LED

 indicates that low voltage power is applied to the circuit board. 

Input LEDs

 should be OFF and 

will only illuminate when an input is activated. P

ulse 1 and 2 LEDs

 will blink as the operator(s) are running. They can be either 

ON or OFF when the operator(s) are stopped. One pulse LED for each operator used (Primary/Secondary). 

Loop LEDs

 will flash 

when each specific 
loop is activated. 

Tracker LEDs

 will 

flash as operator 
data is sent to the 
access controller 
(DoorKing models 
1833, 1835, 1837 
or 1838 only).

Auto-close timer
(when turned ON)
SW 1, switch 4 

ON

Adjust from 1 second 
(full counter clockwise) to 
approximately 23 seconds 
(full clockwise).

Dry relay contacts (terminals 
16-17) can be set for Normally 
Open (NO) or Normally Closed 
(NC) operation by placing the 
relay shorting bar on the N.O. or 
N.C. pins respectively. (Standard 
shadow loop function, NO)

Auto-Close Timer

Dry Relay
Contact

20

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

NC

NO

Set the DIP-switches 
on the circuit board to 
the desired setting.
See switch-setting 
charts on next 2 pages.

DIP-Switches

Tracker

Data

Power

LED

111

12

12

13

14

15

Input LEDs

#9-Pulse 1 LED Primary Operator

4502-010

#10-Pulse 2 LED Secondary Operator

Loop

LED

Board Ground

Loop

LED

DoorKing Plug-In Loop Detectors 

(Sold separately)

EXIT Loop T

erminal

REVERSE/SHADOW

Loop T

erminals

SHADOW

Output T

erminal

EXIT Loop Port

REVERSE Loop Port

9410 Single

Channel

9409 Dual

Channel

Auxiliary Terminal

See page 25.

Secondary

Operator Motor

Terminal

See page 17.

See page 26 for loop info.

ON

123

4

5678

SW1

ON

12345678

SW1

ON

12345678

SW2

1

23

Cycles the 
operator when 
pressed. Will 
use auto close 
timer when 
turned on.

Key Switch

 

Содержание 6050-080











































Отзывы: