DoorKing 6050-080 Скачать руководство пользователя | Manualshive

Страница: 18 / 42

background image

6050-065-C-2-16

14

Potential Entrapment Area:

If the

CLOSING

gate could cause an entrapment,

then installation of a

MONITORED

entrapment

protection device is

REQUIRED

.

Typical Monitored Reversing Edge mounted on end of gate.

Greater than 6” but less than 16”

Gate Frame (Closed)

1.9 Continued

Monitored

Reversing

Edge

Edge

Transmitter

Gate Frame (Closed)

Reversing Edge

Edge

Transmitter

See page 25 for aux terminal wiring
for monitored reversing edge.

A monitored reversing edge (Type B2) should be installed as entrapment protection for the closing cycle of the gate.

Typical Reversing Edge mounted on

bottom of gate when necessary.

If the bottom of gate is greater than 6” but less than
16” above the ground

at any point in its arc of

travel

, it is recommended mounting

a reversing edge for safety.

OPTIONAL wireless transmitter can be used.

OPTIONAL wireless transmitter can be used.

Close-Direction Monitored Reversing Edge

Potential

Entrapment

Area

Closing Gate

Mointored Sensor Note:

Input is active in both directions of travel.

«
...
16
17
18
19
20
...
»

Содержание 6050-080











































Отзывы:

Нет отзывов

Похожие инструкции для 6050-080

Бренд: FAAC Страницы: 29

Бренд: FAAC Страницы: 28

Бренд: FAAC Страницы: 54

SeceuroGlide Compact

Бренд: SWS Страницы: 12

Бренд: SOMFY Страницы: 72

Бренд: Homentry Страницы: 16

Security+ 257856

Бренд: Chamberlain Страницы: 88

Бренд: FlexiForce Страницы: 16

Бренд: V2 Страницы: 38

Бренд: FAAC Страницы: 42

Бренд: CAME Страницы: 28

Бренд: tau Страницы: 11

Бренд: DoorHan Страницы: 28

Бренд: Wayne-Dalton Страницы: 11

Бренд: Raynor Страницы: 36

Бренд: Glide Страницы: 17

Бренд: Proctor-Silex Страницы: 5

Бренд: Centurion Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды