Docomo FOMA P706ie, Инструкция по эксплуатации, Страница: 118 / 577

116
S
e
cu
rity S
e
ttin
g
s
For some functions of the FOMA phone, you need to enter your
password. In addition to the Terminal Security Code for operating
respective mobile phone functions, the Network Security Code to use
network services, and i-mode password are available. These passwords
help you utilize your FOMA phone.
The Terminal Security Code is set to “0000” at purchase but you can
change it by yourself. (See page 117)
When the display for entering the Terminal Security Code appears, enter
your four- to eight-digit code and press
O o
( ).
≥
When you enter your Terminal Security Code, the entered
numbers are indicated by “_” and not displayed.
≥
If you have entered wrong numbers or nothing for about 15
seconds, a warning tone sounds and a warning message is
displayed; then the display prior to entering the Terminal
Security Code returns. Check the correct code and retry entering numbers.
Passwords
■ Cautions on passwords
≥
You should avoid using the numbers for passwords such as denoting your birth date,
part of your phone number, local address number, room number, “1111” or “1234”
that is easily decoded by a third party. Also make sure that you take a note of the
passwords you have selected just in case you forget them.
≥
Take care not to let others know your passwords. Even if your passwords are known
and used by a third party, we at DOCOMO take no responsibility in any event for the
resultant loss.
≥
Note that we at DOCOMO will never make any inquiries about your passwords.
≥
If you do not remember your respective passwords, you need to bring an
identification card such as your driver’s license, the FOMA phone and UIM to the
handling counter of a DOCOMO shop.
For details contact “DOCOMO Information Center” on the back page of this manual.
Terminal Security Code
The Network Security Code is a four-digit number for procedures on
DOCOMO e-site or for using network services. This is determined at the
time of contract but can be changed by yourself.
If you have “docomo ID/Password” for “My docomo”, the overall support
site for personal computers, you can use a personal computer to take
proceedings of changing your Network Security Code to new one. Also,
you can change it by yourself from “
各種手続き (procedures)” on
DOCOMO e-site by using the i-mode phone.
※ For “My docomo” and “DOCOMO e-site ( ドコモ e サイト )”, see the back
of the back page of this manual.
You need to enter the four-digit “i-mode password” for registering or
deleting My Menu, applying for or canceling Message Services, i-mode
pay service, and so on. (Some information providers may provide you
with their specific password.)
The i-mode password is “0000” at the time of your contract, but you can
change it by yourself. (See page 159)
From i-mode, you can change the i-mode password by following
operation:
“
i
Menu” → “English” → “Options” → “Change i-mode Password”
For the UIM, you can set the two security codes, namely the PIN1 code
and PIN2 code. These security codes are “0000” at the time of your
contract, but you can change them by yourself. (See page 118)
The PIN1 code is the four- to eight-digit number for checking the user
each time the UIM is inserted into the FOMA phone or each time the
FOMA phone is turned on, so that you can prevent the third party from
using your UIM. By entering your PIN1 code, you can make or answer
calls, or use functions in the FOMA phone.
The PIN2 code is the four- to eight-digit number for executing Reset Total
Cost, using the user certificate or applying for the issue of it, etc.
≥
If you purchase a new FOMA phone and use the existing UIM with the new FOMA
phone, use the PIN1 code and PIN2 code you have set previously.
Network Security Code
i-mode Password
PIN1 Code/PIN2 Code