Docomo FOMA P704IU, Руководство пользователя

Страница: 517 / 528

48
AT Command List
AT command Outline Parameter/Explanation
Command execution
example
A/
[M]
Re-executes the last
executed command. No
carriage return is required.
−
A/
OK
AT%V
[M]
Displays the version of the
FOMA phone.
−
AT%V
Ver1.00
OK
AT&Cn
[M]
[&F][&W] Selects the operating
conditions of the circuit CD
signal sent to the DTE. n=0: CD is always ON.
n=1: CD varies according to the carrier of the
other party’s modem. (default)
AT&C1
OK
AT&Dn
[M]
[&F][&W]
Selects an operation to be
performed when the circuit
ER signal received from the
DTE transits from ON to
OFF. n=0: Ignores the ER status. (Always assumed to
be ON.)
n=1: Sets the online command state when the
ER changes from ON to OFF.
n=2: Sets the of
fl
ine command state when the
ER changes from ON to OFF. (default)
AT&D1
OK
AT&En
[M]
[&F][&W] Selects the speed display
speci
fi
cation for connection.
n=0: Displays communication speed between
radio wave blocks.
n=1: Displays DTE serial communication speed.
(default)
AT&E0
OK
AT&Fn
[AT][M]
Returns all registers to
the default. Performs line
disconnection processing
if you enter this command
during communication. Only n=0 is speci
fi
able. (Can be omitted)
−
AT&Sn
[M]
[&F][&W] Speci
fi
es the control of the
data set ready signal to be
output to the DTE.
n=0: DR is always ON. (default)
n=1: DR is set to ON at connection of the line
(at establishment of a communication call).
AT&S0
OK
AT&Wn
[M] Stores the current set
values. Only n=0 is speci
fi
able. (Can be omitted)
−
AT ½ DANTE
[AT][M]
Shows the number of
antenna bars. (0 to 3) =0: Antenna shows the out of the service area
=1: Zero antenna bars or a single antenna bar
=2: Two antenna bars
=3: Three antenna bars AT ½ DANTE
½
DANTE:3
OK
AT
½
DANTE=?
½
DANTE:(0-3)
OK
AT
½
DGANSM=n
[M]
Sets the reject/accept setting
mode for the packet incoming
call.
The setting with this command is
valid for incoming calls in packet
communication after you enter
the setting command. n=0: Invalidates the incoming call reject/accept
setting. (default)
n=1: Validates the incoming call reject setting
(AT
½
DGARL).
n=2: Validates the incoming call accept setting
(AT
½
DGAPL).
AT
½
DGANSM?: Displays the current setting.
AT
½
DGANSM=0
OK
AT
½
DGANSM?
½
DGANSM:0
OK
AT
½
DGAPL=n
[,cid]
[M]
Sets the APN of which
packet incoming call is to be
accepted.
To specify the APN, use the
<cid> parameter de
fi
ned in
AT+CGDCONT.
n=0: Adds the APN de
fi
ned by <cid> to the
incoming call accept list.
n=1: Deletes the APN de
fi
ned by <cid> from the
incoming call accept list.
Applied to all the cid contents if <cid> is omitted.
AT ½ DGAPL?: Displays the incoming call accept list.
AT
½
DGAPL=0,1
OK
AT
½
DGAPL?
½
DGAPL:1
OK
AT
½
DGAPL=1
OK
AT
½ DGAPL?
OK
AT
½
DGARL=n
[,cid]
[M]
Sets the APN of which
packet incoming call is to be
rejected.
To specify the APN, use the
<cid> parameter de
fi
ned in
+CGDCONT.
n=0: Adds the APN de
fi
ned by <cid> to the
incoming call reject list.
n=1: Deletes the APN de
fi
ned by <cid> from the
incoming call reject list.
Applied to all the cid contents if <cid> is omitted.
AT
½
DGARL?: Displays the incoming call reject list.
AT
½
DGARL=0,1
OK
AT
½
DGARL?
½
DGARL:1
OK
AT
½ DGARL=1
OK
AT
½
DGARL?
OK
0GZV2CIG 0GZV2CIG