DoAll TF-2025M, Инструкция по эксплуатации

Страница: 15 / 34

11
CUTTING CAPACITY
1. The standard machine's cutting capacity is:
• At 0° tilt: 20 inches (508.0 mm) wide by 25 inches
(635.0 mm) high for rectangular stock; 20 inches
(508.0 mm) diameter for round stock.
• At 45° tilt: 20 inches (508.0 mm) wide by 17 inches
(431.8 mm) high for rectangular stock; 17 inches
(431.8 mm) diameter for round stock.
• At 60° tilt: 20 inches (508.0 mm) wide by 11 inches
(279.4 mm) high for rectangular stock; 11 inches
(279.4 mm) diameter for round stock.
2. Cutting capacity may vary with addition of accessories
and will be noted when applicable.
Vse Capacty
1. The vise maximum opening is 20.50 inches (520.7
mm).
• Weight limit for the vise bed is approximately 1000
pounds (453.6 kg); 500 pounds (226.8 kg) for each
half evenly distributed with no impact.
Saw Band Recommendatons
1. A high-speed DoALL Imperial Bi-Metal Super
Silencer saw band with protective Saw Cap is
supplied with the machine. Band length is 209
inches (5308.6 mm); width is 1-1/4 inches (31.7
mm); recommended gage is 0.042-inch (1.1 mm);
kerf is 0.085-inch (2.2 mm).
2. A machine in correct adjustment, good operating
condition and using proper cutting fluid is essential
to efficient sawing.
3. Proper blade care should include: (a) Pushing uncut
stock away from the saw band; (b) Using correct
band speed, feed force and cutting fluids during
operation; (c) Removing scale from stock before
sawing; (d) Keeping the protective Saw Cap over
blade teeth until installation time.
Consult your DoALL sales representatve for
complete nformaton about saw bands and
ther applcatons.
CONTROL CONSOLE
Electrcal Controls
1. Left Lft Roller (Optonal). This selector switch
operates the left hand (inboard) lift roller in the "UP"
or "DOWN" positions.
2. Left Vse . This selector switch with "OPEN", "HOLD"'
and "CLAMP" settings operate the vise on the left
side (inboard side) of the saw band.
• The "OPEN" setting opens the vise jaws; the
"CLAMP" setting closes the vise jaws; and "HOLD"
stops vise jaw movement, t does not clamp
materal .
• This vise must be clamped to start the band drive.
3. Saw Head Control. Use this selector switch
with "REV" (reverse), "HOLD" and "FWD/AUTO"
("FORWARD/AUTO") settings to regulate the
direction of saw head movement.
• Rotating the selector to "FWD/AUTO" or forward
moves the saw head forward or towards the sawing
area.
• Rotating the selector to "REV" or reverse moves
the saw head back or away from the sawing area.
• Turning the selector switch to "HOLD" stops all saw
feed motion.
4. Rght Lft Roller (Optonal). This selector switch
operates the right hand (outboard) lift roller in the
"UP" or "DOWN" positions.
5. Rght Vse (Optonal) . This selector switch with
"OPEN", "HOLD"' and "CLAMP" settings operate
the vise on the right side (outboard side) of the saw
band.
• The "OPEN" setting opens the vise jaws; the
"CLAMP" setting closes the vise jaws; and "HOLD"
stops vise jaw movement.
Make sure the vse jaw s opened wde enough
when movng materal through the vses.
6. Head Rapd Approach. Used in conjunction with
the Saw Head Control selector switch, pushing
and holding this pushbutton accelerates the rate
of speed the saw head moves towards the sawing
area.
• This pushbutton is active only when the Saw Head
Control selector is in the "FWD/AUTO" position. The
band drive does not have to be "ON" to operate.
7. Laser. This selector switch turns the line-up laser
"ON" and "OFF".
To avod eye damage, DO NOT stare nto the
laser beam.