Ditch Witch 420sx Скачать руководство пользователя страница 69

Страница: 69 / 141

Plow - 68

420sx Operator’s Manual

Operation

CMW

11. When installation is complete, move ground drive control to the neutral position.

12. Engage parking brake.

13. Ensure that attachment speed switch is in the LOW position.

14. With vibrator running, lower throttle speed and raise plow to just below ground level.

15. Turn vibrator switch to OFF.

16. Raise the plow blade out of the ground.

17. Turn ignition switch to STOP and remove product from plow.

18. Start tractor and drive a short distance away from work site.

19. Shut down tractor. See page 52 for proper shutdown procedures.

NOTICE:

Do not operate vibrator when plow is out of the ground. This will cause excessive

vibration and will cause rapid wear, and possible damage to the unit and product being
installed.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды