Ditch Witch 420sx Скачать руководство пользователя страница 21

Страница: 21 / 141

Safety - 20

420sx Operator’s Manual

Safety Alerts

CMW

Moving traffic - hazardous situation. Death or serious injury could result.

Avoid moving vehicles, wear high visibility clothing, post appropriate warning signs.

Hot pressurized cooling system fluid could cause serious burns. Allow to

cool before servicing.

Flying objects may cause injury. Wear hard hat and safety glasses.

Hot parts may cause burns. Do not touch until cool.

Exposure to high noise levels may cause hearing loss. Wear hearing

protection.

Fall possible. Slips or trips may result in injury. Keep area clean.

Battery acid may cause burns. Avoid contact.

Improper handling or use of chemicals may result in illness, injury, or

equipment damage. Follow instructions on labels and in material safety data sheets
(MSDS).

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды