Ditch Witch 420sx Скачать руководство пользователя страница 20

Страница: 20 / 141

420sx Operator’s Manual

Safety - 19

Safety Alerts

CMW

Explosion possible. Serious injury or equipment damage could occur.

Follow directions carefully.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

Fall possible. Riders can fall from machine and be injured or killed. Only

operator is allowed on machine.

Rollover possible. If machine rolls over, you could be thrown from seat and

killed or crushed. Wear seat belt.

Improper control function could cause death or serious injury. If control does

not work as described in instructions, stop machine and have it serviced.

Looking into fiber optic cable could result in permanent vision damage. Do

not look into ends of fiber optic or unidentified cable.

Pressurized fluid or air could pierce skin and cause injury or

death. Stay away.

Runaway possible. Machine could run over you or others. Learn how to use

all controls. Start and operate only from operator’s position.

Fire or explosion possible. Fumes could ignite and cause burns. No

smoking, no flame, no spark.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды