Ditch Witch 420sx Скачать руководство пользователя страница 23

Страница: 23 / 141

Safety - 22

420sx Operator’s Manual

Emergency Procedures

CMW

If an Electric Line is Damaged

If you suspect an electric line has been damaged and you are

on tractor

, DO NOT MOVE. Remain on

tractor and take the following actions. The order and degree of action will depend upon the situation.

•

Warn people nearby that an electric strike has occurred. Instruct them to leave the area and contact
utility.

•

Raise attachments and drive from immediate area.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

If you suspect an electric line has been damaged and you are

off tractor

, DO NOT TOUCH TRACTOR.

Take the following actions. The order and degree of action will depend upon the situation.

•

LEAVE AREA. The ground surface may be electrified, so take small steps with feet close together to
reduce the hazard of being shocked from one foot to the other. For more information, contact your
Ditch Witch dealer.

•

Contact utility company to shut off power.

•

Do not return to jobsite or allow anyone into area until given permission by utility company.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды