Ditch Witch 420sx Скачать руководство пользователя страница 51

Страница: 51 / 141

Drive - 50

420sx Operator’s Manual

Start Unit

CMW

Start Unit

Before operating tractor, read engine manufacturer’s starting and operating instructions. Follow
instructions for new engine break-in.

Runaway possible. Machine could run over you or others. Learn how to

use all controls. Start and operate only from operator’s position.

Incorrect procedures could result in death, injury, or property damage.

Learn to use equipment correctly.

NOTICE:

•

Read operator’s manual before operating equipment. Follow instructions carefully. Contact your
Ditch Witch dealer for operation information or demonstration.

•

Wear hard hat, safety glasses, and other protective equipment required by job. Do not wear jewelry
or loose clothing that can catch on controls.

Rollover possible. If machine rolls over, you could be thrown from seat

and killed or crushed.

See “Roll-Over Protective Structure” on page 86.

NOTICE:

•

Wear seat belt and keep the ROPS in the upright position during normal operation.

•

Do not wear seat belt when ROPS is folded down.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды