manualshive.com logo in svg

Ditch Witch 420sx, Руководство оператора

Поделиться
Скачать
Ditch Witch 420sx Скачать руководство пользователя страница 90

420sx Operator’s Manual

Systems and Equipment - 89

Chain, Teeth, and Sprockets

Chain, Teeth, and Sprockets

Chain and Tooth Maintenance

•

Always replace sprockets at the same time you replace the digging chain. Sprockets and chain are 
designed to work together. Replacing one without the other will cause premature wear of the new part. 

•

Do not use worn teeth. Using dull, worn teeth will decrease production and increase shock load to 
other trencher components. It can also cause chain stretch, which leads to premature chain wear and 
failure.

•

Maintain the proper amount of tension on the digging chain. Overtightening will cause chain stretch 
and loss of machine performance. For correct tightening procedure, see page 108.

•

Use the tooth pattern most appropriate for your digging conditions. If you move to a different soil type, 
contact your Ditch Witch dealer for information about the most effective chain type and tooth pattern.

Chain Types

Chain type

Features

4-pitch

standard chain

2-pitch

more teeth for smoother cutting

alternating side bar

prevents spoil compaction on chain

bolt-on adapters

allow easy configuration changes

Shark Chain II

versatile, virtually maintenance-free

combination

provides pick and shovel effect

Содержание 420sx














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды