Ditch Witch 420sx Скачать руководство пользователя страница 22

Страница: 22 / 141

420sx Operator’s Manual

Safety - 21

Emergency Procedures

CMW

Emergency Procedures

Before operating any equipment, review emergency procedures and check that all safety precautions have
been taken.

Electric Strike Description

When working near electric cables, remember the following:

•

Electricity follows all paths to ground, not just path of least resistance.

•

Pipes, hoses, and cables will conduct electricity back to all equipment.

•

Low voltage current can injure or kill. Almost one-third of work-related electrocutions result from
contact with less than 440 volts.

Most electric strikes are not noticeable, but indications of a strike include:

•

power outage

•

smoke

•

explosion

•

popping noises

•

arcing electricity

If any of these occur, assume an electric strike has occurred.

Jobsite hazards could cause death or serious injury. Use

correct equipment and work methods. Use and maintain proper safety
equipment.

EMERGENCY SHUTDOWN

- Turn ignition switch to stop position or push remote engine stop button (if

equipped).

Electric shock. Contacting electric lines will cause death or serious injury.

Know location of lines and stay away.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды