manualshive.com logo in svg

Ditch Witch 420sx, Руководство оператора

Поделиться
Скачать
Ditch Witch 420sx Скачать руководство пользователя страница 4

420sx Operator’s Manual

Overview - 3

Intended Use

CMW

Intended Use

The 420sx is a 41 hp (30 kW), ride-on, articulated vibratory plow designed to install communication, gas, 
and electrical lines as well as lawn irrigation systems up to 3” (76 mm) in diameter and up to a 24” (610 
mm) cover depth. Optional equipment includes digging boom with 36” (914 mm) maximum depth and 6” 
(152 mm) trench width capabilities, front reel carrier, specialized rear reel carrier, light kit, and Roto Witch

®

 

drilling attachment.

The unit is designed for operation in temperatures typically experienced in excavation and construction 
work environments. Provisions may be required to operate in extreme temperatures. Contact your Ditch 
Witch dealer. Use in any other way is considered contrary to the intended use. 

The H401 trencher should be used with genuine Ditch Witch chain, teeth, and sprockets. The 420sx 
should be operated, serviced, and repaired only by persons familiar with its particular characteristics and 
acquainted with the relevant safety procedures.

Содержание 420sx














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды