manualshive.com logo in svg

Ditch Witch 420sx, Руководство оператора

Поделиться
Скачать
Ditch Witch 420sx Скачать руководство пользователя страница 70

420sx Operator’s Manual

Plow - 69

Operating Tips

CMW

Operating Tips

•

Choose the correct plow blade for the type of material being installed. Consider bend radius and 
diameter of material being installed as well as depth of installation.

•

If material must be at a constant depth, dig starting and target trenches.

•

Hand feed material through feed tube when raising and lowering the plow to prevent excess bending of 
material. 

•

Check material for damage during plowing. Run continuity checks on electric cable and check pipe 
pressure. Damage can result from improper operation, incorrect blade choice, striking underground 
obstructions, or other conditions.

•

Use optional sod cutter when plowing in areas with heavy grass cover or surface clutter.

•

Do not plow with overtravel bumpers in 
contact with trolley (shown) for more than a 
few minutes. Use the plow position indicator 
and alignment marks to keep the plow 
centered in the trolley.

Содержание 420sx














































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды