Ditch Witch 420sx Скачать руководство пользователя страница 60

Страница: 60 / 141

420sx Operator’s Manual

Transport - 59

Haul

CMW

Unload

1. Lower trailer or ramps.

2. Remove chains from tiedowns.

3. Disengage frame lock.

4. Ensure that ROPS is locked in the upright position.

5. Fasten and adjust seat belt.

6. Start tractor. See page 50 for proper start-up procedures.

7. Raise trencher boom, but keep it low.

8. Fully raise or remove plow blade.

9. Disengage parking brake.

10. Slowly back unit down trailer or ramps.

Crushing weight. If load falls or moves it could kill or crush you. Use

proper procedures and equipment or stay away.

NOTICE:

•

Attach trailer to tow vehicle before loading or unloading.

•

Load and unload trailer on level ground.

•

Turn off ignition. Set parking brake.

•

Block trailer wheels.

•

Incorrect loading can cause trailer swaying.

Rollover possible. If machine rolls over, you could be thrown from seat

and killed or crushed. Wear seat belt.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды