Ditch Witch 420sx Скачать руководство пользователя страница 53

Страница: 53 / 141

Drive - 52

420sx Operator’s Manual

Drive

CMW

Drive

1. Turn on lights as needed.

2. Raise attachments.

3. Release parking brake.

4. Adjust throttle.

5. Move ground drive joystick in desired direction of travel. For information about the ground drive

joystick, see page 31.

Shut Down

1. When job is complete, move ground drive joystick to neutral.

2. Return all controls and rocker switches to neutral or disengaged position.

3. Engage parking brake.

4. Lower all attachments to ground.

5. Move throttle to idle for 3 minutes to cool.

6. Turn ignition switch to STOP. If leaving machine unattended, remove key.

7. For maintenance or long-term storage, turn battery disconnect switch, if equipped, to the disconnect

position.

EMERGENCY SHUTDOWN

: Turn ignition switch to STOP.

Moving traffic – hazardous situation. Death or serious injury could result.

Avoid moving vehicles, wear high visibility clothing, post appropriate warning signs.

NOTICE:

•

Drive carefully in congested areas. Know machine’s clearance and turning radius.

•

Keep attachments low when operating on slope. Drive slowly and cautiously.

Содержание 420sx














































































































































Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды

Ditch Witch 420sx, Руководство оператора

Результаты поиска

Содержание 420sx

Отзывы:

Бренды по названию

Популярные бренды