Desert Aire LW Скачать руководство пользователя страница 34

Страница: 34 / 54

Specific items should be noted before the replacement to give the best

indications of the failure and complete the diagnosis as the new compressor is

installed.

The following data should be taken to assist in diagnosis:

•

Current draw for each leg of power (if the compressor will run and

pump).

•

High side and low side pressure (if the compressor will run and pump).

•

Resistance of each leg to leg on three phase compressor or each leg

to neutral on single phase compressors.

•

Check of continuity from each leg to ground.

•

Review of all system alarms including the relative timing of the alarms

and mode of operation.

It is important to note that other components or lines may have been damaged

if the compressor has failed. At times the internal damage to a compressor

creates extreme levels of vibration before complete failure.

Refrigeration lines and connections may be damaged before the compressor

stops. Inspect tubing and components of the system before completing the

compressor replacement.

Compressor Replacement

•

Refrigeration oil must be tested for acid and particulate during any

compressor replacement. For the initial testing, the compressor sump

should be used to sample the oil. Oil can be recovered through the

Schrader port on the low point compressor shell or through the suction

line connection after the compressor has been removed.

•

Use Virginia KMP, New-Calgon Phase III, Sporlan Test-All, or

equivalent oil test where oil is sampled into a container. Vapor

sampling methods may not show particulate and should not be used.

•

Read the oil test kit manufacturer’s instructions to determine if there is

acid present in the oil. Determine if there are other contaminants by

viewing the samples for darkness, cloudness, or particulate.

The following procedures must be used depending on the results of the test above:

Any

Compressor

Service

•

A new filter dryer must be installed when the system has been

opened. If there is no acid or particulates indicated, the new

compressor can be installed and run. Proceed to Testing and Final

Diagnosis.

Desert Aire - LW Manual

Содержание LW























































Результаты поиска

Содержание LW

Отзывы:

Похожие инструкции для LW

Бренды по названию

Популярные бренды

Desert Aire LW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LW

Отзывы:

Похожие инструкции для LW

Бренды по названию

Популярные бренды