Desert Aire LW Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 54

background image

17

2.4.2 Wire and Fuse Sizing

The field-installed power supply wires and overcurrent devices must be sized to

handle the minimum ampacity of the dehumidifier without exceeding the maximum

fuse size rating. Both the minimum ampacity and the maximum fuse size are printed

on the unit rating plate.

2.5

Controls and Wiring

The standard Desert Aire LW Series dehumidifiers are controlled by the CM3540

microprocessor controller. This controller is designed for precise monitoring and control of

air temperature and relative humidity (RH) within a conditioned environment. A separate

controls manual has been provided. Refer to this separate manual for controller and sensor

specifications, operation, and options.

You will need to run low voltage wires from the controller to the humidity sensor and to the

dehumidifier. The low voltage wiring diagram located on the inside of the dehumidifier’s

electric box door shows where to make wiring connections to the system.

2.6

Remote Condenser (Optional)

Important:

Refer to the separate Air Cooled Condensers Installation and Operation manual

for additional details on line design, traps, clamping, and other condenser installation

requirements.

LW dehumidifiers installed with remote condensers may require additional oil and refrigerant

charge at the time of field installation. Refer to the submittal documentation or label adjacent

to the remote condenser connections to confirm the charge and connection tube sizes.

Desert Aire - LW Manual

«
...
15
16
17
18
19
...
»

Содержание LW























































Отзывы:

Нет отзывов

Похожие инструкции для LW

Comfort SC-AH986M05

Бренд: Scarlett Страницы: 19

Бренд: Aprilaire Страницы: 4

XD COLLECTION P301.12 Series

Бренд: XINDAO Страницы: 36

Бренд: Aprilaire Страницы: 8

Бренд: Zenith Страницы: 36

Бренд: Vitek Страницы: 36

Бренд: RDZ Страницы: 32

Бренд: Air-O-Swiss Страницы: 52

Бренд: Rotel Страницы: 23

Бренд: Munters Страницы: 37

Бренд: Ecor-Pro Страницы: 10

Бренд: Objecto Страницы: 17

Бренд: Fakir Страницы: 56

Бренд: Steamfast Страницы: 12

Бренд: Nortec Страницы: 45

Бренд: Nortec Страницы: 84

Бренд: YAUFEY Страницы: 16

Бренд: NewAir Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды