Desert Aire LW Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 54

Desert Aire LW Скачать руководство пользователя страница 28

28

4.2. Compressor Will Not Run

POSSIBLE CAUSE

Controller settings

Loss of main power

Faulty wiring

Compressor overload has tripped

Comp. failure may have occurred if:

A) Comp. draws locked rotor amps

B) Comp. starts but does not pump

C) Motor windings have shorted

D) Incorrect rotation (reverse

phasing)

NOTE: THE LW SERIES DEHUMIDIFIER

IS DESIGNED FOR A MINIMUM

RETURN AIR TEMPERATURE OF 35°F.

If return air temperature drops below

32°F, an internal thermostat will trip

preventing the compressor from

activating. Operation below 32°F will

accelerate system wear-and-tear and

void the warranty.

REMEDY

A) Adjust controller set-points.

B) On models with a remote

condenser installed, verify that the

condenser is enabled.

Check for tripped circuit breaker or

blown fuses.

Check for loose or faulty wiring on

system and controller.

Inspect the following:

A) elevated head pressure

B) lack of oil to the compressor

C) locked rotor amps (LRA)

D) possible compressor failure

A) Replace compressor (or check

fuses on three-phase units).

B) Replace compressor.

C) Replace compressor.

Heat conditioned air to minimum 35°F.

Note that heating air will also reduce

relative humidity.

Desert Aire - LW Manual

«
...
26
27
28
29
30
...
»

Содержание LW























































Отзывы:

Нет отзывов