Desert Aire LW Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 54

background image

4

Desert Aire - LW Manual

Extended Warranty:

Your Desert Aire unit may have extended warrantees beyond this Standard Limited Warranty document.
Extended warrantees are only available at the time of the purchase of the original equipment. These extended
warrantees are covered under a separate document and their terms and conditions are separate from this
document. It is mentioned in this document for informational purposes only. Any Extended Warranties will be
identified on the Warranty Validation Letter.

Any and all incidental or consequential damages are expressly excluded from this warranty. Some states do not allow
the exclusion of incidental or consequential damages for personal injury, so the above limitations may not apply to you
for certain damages. This warranty gives you specific legal rights, and you may also have other rights, which vary
from state to state. No person or representative is authorized to make any warranty or assume any liability not strictly
in accordance with the aforementioned.

Inquiries regarding warranty matters should be addressed to:

Desert Aire Corp

c/o Service Manager

N120 W18485 Freistadt Road

Germantown, WI 53022

PH: (262) 946-7400

TOLL FREE: (800) 443-5276

FAX: (262) 946-7401

E-MAIL: [email protected]

Additional copies of this manual can be purchased for a nominal fee from Desert Aire. Submit requests to the contact
information listed above.

«
...
2
3
4
5
6
...
»

Содержание LW























































Отзывы:

Нет отзывов

Похожие инструкции для LW

Бренд: East Страницы: 11

Бренд: HoMedics Страницы: 9

Бренд: ACS Страницы: 34

smartDROP EE-5303

Бренд: Crane Страницы: 13

Бренд: Crane Страницы: 12

Klimatronic DryFix 20 Design

Бренд: SUNTEC Страницы: 64

Бренд: BMT Страницы: 9

Бренд: Goldair Страницы: 12

Бренд: Ideal Air Страницы: 4

Бренд: Metro DataVac Страницы: 4

Бренд: Seedmax Страницы: 28

Бренд: Hunter Страницы: 24

Бренд: easywell Страницы: 9

iDRY iRDP CT 30

Бренд: ICP Страницы: 72

Бренд: Olimpia splendid Страницы: 36

Бренд: TCS Страницы: 8

Бренд: Black & Decker Страницы: 26

Variheat AA1200

Бренд: Calorex Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды