Desert Aire LW Скачать руководство пользователя страница 41

Страница: 41 / 54

•

Defrost mode suction temperature range: 30° to 100°F

•

Defrost mode discharge temperature range: 90° to 200°F

NOTE:

Always check the system airflow before you troubleshoot the

refrigeration circuit. (See Section 5.3.1 and 5.3.1.1)

5.4

Component Replacement, Charge, Evacuation, & Leak Instructions

Note that a new liquid line filter dryer will be required any time a refrigeration system is opened for

servicing. New dryer should be of the same capacity as the original or larger.

Recovery

When there has not been a major refrigeration system leak, the system will contain refrigerant. This

refrigerant must be either recovered to separate cylinders appropriate for the refrigerant type or

isolated in a portion of the refrigeration system that will not be open for service. In all cases you must

comply with Section 608 Refrigerant Recycling Rule of the Clean Air Act.

Recovery of Systems with a Refrigeration System Leak

As much refrigerant as possible must be recovered into separate refrigerant cylinders appropriate for

the refrigerant being serviced. System pressure near the leak site should be monitored closely to

ensure this area is not pulled to a vacuum. Isolated sections of the system as required and recover

independently to avoid refrigerant contamination. Uncontaminated refrigerant can be reused in the

refrigeration system it was recovered from.

Recovery of Systems without a Leak

Systems that do not have leaks, but still require refrigeration system service, may have charge

isolated in receivers and condensers if these particular components do not require direct service.

Desert Aire dehumidifiers have different receiver sizes depending on the model and size. Condenser

sizes and configurations may also vary. In general, larger receivers will come equipped with isolation

valves that will allow for a portion of the charge to be contained in the receiver during servicing. Units

equipped with remote condensers will have isolation valves located inside the unit cabinet near the

area where the connections are made.

The compressor can be used to move the refrigerant to the system components that will be used to

temporarily hold the charge. Note that cooling a condenser by running as many fans as possible

and/or cooling the coil surface with a stream of water can assist in storing charge.

The low side pressure should be monitored closely while using this procedure to store charge. Under

no circumstances should a compressor be allowed to run in a vacuum. When most of the refrigerant

is isolated in the condensers, recover remaining charge into separate refrigerant cylinders

Desert Aire - LW Manual

Содержание LW























































Результаты поиска

Содержание LW

Отзывы:

Похожие инструкции для LW

Бренды по названию

Популярные бренды

Desert Aire LW, Инструкция по установке и эксплуатации

Результаты поиска

Содержание LW

Отзывы:

Похожие инструкции для LW

Бренды по названию

Популярные бренды