Desert Aire LW Скачать руководство пользователя страница 23

Страница: 23 / 54

•

Automatic Blower Operation

– the blower can be set to automatic or

continuous operation. Automatic operation will activate the blower on a call

for air dehumidification or air cooling (remote ready models only). The

blower will turn off when all set points are satisfied. Refer to the CM3540

Controller IO Manual for details.

3.3

Refrigeration Testing

Refrigeration based cooling systems are sometimes referred to as “sealed systems”.

This is in reference to the refrigeration system being hermetically sealed, no refrigerant can

leave the system and no contaminants are allowed inside. Factory equipment and procedures

ensure a clean and tight refrigeration system where only the specified refrigerant and oil are

in the system. This is a critical component to the longevity of the system.

Some Desert Aire systems are shipped in sections to allow for installation of some of the

sections in a location much different than another. An example is a unit with a remote

condenser ready circuit. The dehumidifier may be installed indoors near the conditioned

space while the remote condenser used to reject waste heat is located outdoors. The piping

of the condenser is completed in the field before the unit is commissioned. The design and

processing of the field piping is just as important as the factory piping in ensuring the

longevity of the system.

Selection of quality components, quality procedures, and full testing help to ensure the

sealed system failures are minimized wherever possible. Nonetheless, the mechanical

nature of many components creates some unforeseen wear and failure in certain instances.

Some units may need service at a point in the life of the product that requires opening the

hermetic refrigeration system. Special care must be taken to ensure that the system is

returned to service without contamination.

Whenever servicing Desert Aire equipment, observe the following:

•

Use only equipment rated for the pressures of the refrigerant being serviced.

•

Use only equipment dedicated to service of the refrigerant in the system. Do not use

equipment to service multiple refrigerant types.

•

Purge all hoses and equipment of non-condensable gasses before connecting to the

sealed system.

•

Use only original equipment parts or factory approved equivalent for servicing.

•

Use only refrigerant system oil.

•

Minimize the time the system is open to atmosphere while servicing. Cap all

connections when there is no active service work on the system. This is particularly

important with units that contain POE oils as moisture will be absorbed quickly and

cannot be removed with a vacuum.

Desert Aire - LW Manual

Содержание LW























































Результаты поиска

Содержание LW

Отзывы:

Desert Aire LW, Инструкция по установке и эксплуатации, Страница: 23 / 54

Результаты поиска

Содержание LW

Отзывы: