Delta Electronics AC Servo Drive ASDA-AB Скачать руководство пользователя страница 18

Страница: 18 / 357

Chapter 1 Unpacking Check and Model Explanation

ASDA-AB Series

Revision January 2009

1-5

1.3 Servo Drive and Servo Motor Combinations

The table below shows the possible combination of Delta ASDA-AB series servo drives and ECMA series

servo motors. The boxes (

) in the model names are for optional configurations. (Please refer to Section 1.2

for model explanation)

Power

Servo Drive

Servo Motor

100W

ASD-A0111-AB
ASD-A0121-AB

ECMA-C30401

S (S=8mm)

200W

ASD-A0211-AB
ASD-A0221-AB

ECMA-C30602

S (S=14mm)

400W

ASD-A0411-AB
ASD-A0421-AB

ECMA-C30604

S (S=14mm)

ECMA-C30804

7 (7=14mm)

ECMA-E31305

S (S=22mm)

ECMA-G31303

S (S=22mm)

750W

ASD-A0721-AB

ECMA-C30807

S (S=19mm)

ECMA-G31306

S (S=22mm)

1000W ASD-A1021-AB

ECMA-C31010

S (S=22mm)

ECMA-E31310

S (S=22mm)

ECMA-G31309

S (S=22mm)

1500W

ASD-A1521-AB

ECMA-E31315

S (S=22mm)

2000W ASD-A2023-AB

ECMA-C31020

S (S=22mm)

ECMA-E31320

S (S=22mm)

ECMA-E31820

S (S=35mm)

The servo drives shown in the above table are designed for use in combination with the specific servo

motors. Check the specifications of the drives and motors you want to use.

Also, please ensure that both the servo drive and motor are correctly matched for size (power rating). If the

power of motor and drive is not within the specifications, the drive and motor may overheat and servo alarm

would be activated. For the detail specifications of servo drives and motors, please refer to Chapter 11

“Specifications”.

The drives shown in the above table are designed according to the three multiple of rated current of motors

shown in the above table. If the drives which are designed according to the six multiple of rated current of

motors are needed, please contact our distributors or your local Delta sales representative.

Содержание AC Servo Drive ASDA-AB






































































































































































































































































































































































Результаты поиска

Содержание AC Servo Drive ASDA-AB

Отзывы:

Похожие инструкции для AC Servo Drive ASDA-AB

Бренды по названию

Популярные бренды

Delta Electronics AC Servo Drive ASDA-AB, Руководство пользователя

Результаты поиска

Содержание AC Servo Drive ASDA-AB

Отзывы:

Похожие инструкции для AC Servo Drive ASDA-AB

Бренды по названию

Популярные бренды