Dell PowerVault 750N Скачать руководство пользователя страница 78

Страница: 78 / 156

5-6

System Recover y, Backup, and Restore

.co

ll.c

Click

Next

The

How to Restore

window displays.

Click

Always replace the files on disk

Click

Next

The

Advanced Restore Options

window displays.

Leave all checkboxes unchecked.

Click

Next

Click

Finish

to initiate the restore process

Restart your system after the restore process completes.

NOTE:

Windows must replace all locked files on the system; therefore, the restart system

process might take approximately 15 minutes to complete.

Windows 2000 Backup and Recovery Tools

Windows 2000 Backup and Recovery Tools allow you to back up your data volumes to a
locally attached tape drive or to a file.

NOTE:

You must have a supported SCSI card installed and have a tape drive to back up your

data volumes to tape.

You can get to the Windows 2000

Backup and Recovery Tools

by clicking the

Maintenance

tab on the NAS Manager primary menu and clicking

Backup

or by clicking

Windows 2000

Backup/Recovery Tools

on the

Advanced Administration Menu

under

Administrative

Tools

For more information on the

Windows 2000 Backup and Recovery Tools

, see the Windows

Powered Help. You can access Windows Powered Help by clicking

Windows Powered Help

in the

Advanced Administration Menu

under

Administrative Tools

or by clicking

Help

the

Start Menu

when using the

Terminal Services Client

Supported Third-Party Backup Software

• VERITAS

Backup Exec

– Backup Exec 8.0, 8.5, and 8.6 for Windows NT

and Windows 2000

Содержание PowerVault 750N





























































































































































Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды

Dell PowerVault 750N, Руководство системного администратора

Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды