Dell PowerVault 750N Скачать руководство пользователя страница 148

Страница: 148 / 156

9-6

Troubleshooting

.co

ll.c

I have just brought my new

NAS appliance up on the

network, but I am unable to

upload files using FTP even

though I am the

administrator.

By default, no user has write

privileges on the default FTP

site.

The FTP permissions must be

configured using the

Microsoft Management

Console (MMC). To get to

the MMC, click

Computer

Management

on the

Advanced Administration

Menu

, which is available

through Terminal Services.

See the online help for specific

information about configuring

this service.

I have deleted an FTP share

and folder from my NAS

appliance. However, when I

use Terminal Services to

confirm the removal, I can still

see the shared folder in the

FTP section of the MMC.

By default, this folder is not

deleted by the PowerVault

NAS Manager.

Manually remove this listing

from the listed shared folders

in the FTP section of the

MMC.

I cannot use the

Back

button

in Netscape Navigator for the

Online Help in the PowerVault

NAS Manager.

This feature is not supported.

Use the

Previous Topic

link to

navigate back to earlier topics.

I am using Netscape Navigator

to administer my NAS

appliance through the

PowerVault NAS manager. A

long gray bar at the bottom of

the screen is covering the

and

Cancel

buttons.

The page has not finished

Use one of the following

resolutions:

• Wait for the page to finish

• Refresh the page several

times.

Ta b l e 9 - 1 .

Tr o u b l e s h o o t i n g I s s u e s

Issue

Possible cause

Resolution

Содержание PowerVault 750N





























































































































































Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды

Dell PowerVault 750N, Руководство системного администратора

Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды