Dell PowerVault 750N Скачать руководство пользователя страница 103

Страница: 103 / 156

Advanced Features

7-5

If an

Insert Disk

windows appears, you must perform the following procedure:

Click

From the

Files needed

window, click

Browse

and browse to the

i386

directory on

the

Localization

CD (if not already selected).

Click

Open

and then click

from the

Insert Disk

window to allow the

operating system to find the required files for installation.

After the installation is complete, you need to reboot your system.

NOTE:

For more information, see the Microsoft Windows Powered operating system’s online

Help.

Network Adapter Teaming

Adapter teaming allows the system to use the combined throughput of network adapters in
parallel to increase performance or provide fault tolerance. Technologies supported by
teaming are:

• Link aggregation supports scalable bandwidth up to 800 megabits per second (Mbps)

full duplex, or up to eight gigabits per second (Gbps) in a Gigabit Ethernet

environment. Link aggregation requires support in the network interface controller

(NIC) and the switch.

• Cisco’s Fast Ether Channel (FEC) supports scalable bandwidth up to 800 Mbps at full

duplex. FEC requires support in the NIC and the switch.

• Broadcom's Smart Load Balance and Fail Over, supported by Broadcom's Advanced

Server Program Driver, offers a simple method to team two Alteon or Broadcom

Gigabit Ethernet adapters together to provide load balancing and fail over. The

program also allows an onboard Intel

NIC to a member of a team to provide fail over

only capabilities.
When you install multiple Alteon or Broadcom Gigabit Ethernet adapters in the same

server, you can pair them into teams to provide redundant adapter operation in the

event of network failure. You can configure up to two teams, each with two adapters,

on each server. If traffic is not seen on the primary adapter connection in a team failure

of the adapter, cable, switch port, or switch (where the teamed adapters are attached

to separate switches), the secondary team member becomes active, taking the MAC

and IP address originally assigned to the primary adapter. Sessions should be

maintained, causing no impact to the user.

NOTE:

Alteon or Broadcom Gigabit Ethernet adapters can be grouped into failover teams

with an Intel 82559 LAN on motherboard (LOM); however, assigning a LOM to be a
primary adapter is not supported.

Содержание PowerVault 750N





























































































































































Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды

Dell PowerVault 750N, Руководство системного администратора

Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды