Dell PowerVault 750N Скачать руководство пользователя страница 56

Страница: 56 / 156

3-10

Advanced Disk and Volume Management Using Array Manager

.co

ll.c

Array Disk Commands

This section describes the following commands for working with array disks.

• Format
• Rebuild
• Assign a global hot spare
• Unassign a global hot spare
• Online array disk
• Offline array disk
• Prepare to remove
• Properties

Format

The

Format

command performs a low-level formatting of the array disk. To format the array

disk, perform the following steps:

Right-click the disk that you want to format.

Click

Format

The right pane shows the status of the format. The status displays

Formatting

until

the operation is finished.

Rebuild

The

Rebuild

command is enabled only when a disk is failed. You can rebuild only on failed

disks in redundant arrays (RAID 1 or RAID 5) by performing the following steps:

Right-click the failed disk that you want to rebuild.

Click

Rebuild

In the right pane, the status of the disk is

Rebuilding

and a progress bar shows the

percentage of completion.

NOTE:

This process may take several hours.

Содержание PowerVault 750N





























































































































































Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды

Dell PowerVault 750N, Руководство системного администратора

Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды