Dell PowerVault 750N Скачать руководство пользователя страница 129

Страница: 129 / 156

Advanced Features

7-31

If you select

VT100/220

but not all the characters are visible on the screen, you should go

back to the system setup program and select

ANSI

as your terminal type. ANSI can display

the full set of ASCII characters.

Configuring Console Redirection on the Client System

NOTE:

The examples in this document assume that you have upgraded to Hilgraeve’s

HyperTerminal Private Edition 6.1 or later. If you are using other terminal emulation software,
see the help file for that software.

Configuring the Ports

Click the

Start

button, point to

Programs—> Accessories—> Communications

, and

click

HyperTerminal

Enter any name for the new connection and select any icon.

Click

From the

Connect to

pulldown menu, select a COM port available on your client

system and click

After you have selected an available COM port, the COM port properties window is

displayed.

Select

Bits per second

Console redirection supports 9600, 19.2K, 57.6K, or 115.2K bps.

Set

Data bits

Set

Parity

None

Set

Stop bits

Set

Flow control

Hardware

Click

Configuring the Terminal Settings

After you configure the ports, configure the terminal settings by performing the following
steps:

In HyperTerminal, click

File

, click

Properties

, and select the

Settings

tab.

Make sure that the

Function, arrow, and ctrl keys act as

field is set to

Terminal Keys

Make sure that the

Backspace key sends

field is set to

Ctrl+H

Содержание PowerVault 750N





























































































































































Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды

Dell PowerVault 750N, Руководство системного администратора

Результаты поиска

Содержание PowerVault 750N

Отзывы:

Похожие инструкции для PowerVault 750N

Бренды по названию

Популярные бренды