Del ozone TrioPure 25 Скачать руководство пользователя страница 26

Страница: 26 / 31

TrioPure

Sanitation System

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

Problem Cause(s) Solution(s)

Water Flow Indicator turns red & Chlorine Production displays

A) Water flow to the

TrioPure

was restricted

due to an obstruction in

the system.

A) Turn the power off to the TrioPure

and main pool

circuit breaker. Check pool equipment for obstructions,

and remove as necessary. Check filter, clean or pump

to waste as required. Turn the pool pump on and then

the TrioPure

back on – both

Water Flow

and

Ozone

Production

cell indicators should return to gree

B) Flow switch has

become disconnected

from the TrioPure

enclosure.

B) Turn the power off to the TrioPure

and main pool cir-

cuit breaker.

Check the wiring from the flow switch to the

main harness on the right side of the enclosure and recon-

nect if necessary. Turn the power on to the TrioPure

and

main pool circuit breaker and check that both

Water

Flow

and

Ozone Production

cell indicators are green.

Water Temperature Indicator turns red & Chlorine Production displays

A) Water is too hot.

A) Lower the pool’s water temperature to less than

40°C. The

Water Temp

indicator should return to

green when the pool temperature is back within the

TrioPure’s specified limits.

B) Water is too cold.

B) Raise the pool’s water temperature to more than

15°C. The

Water Temp

indicator should return to

green when the pool temperature is back within the

TrioPure’s specified limits.

C) Temperature sensor

has become discon-

nected from the TP

enclosure.

C) Reconnect sensor.

Chlorine Production

display reads

A) The salt chlorinator is

in Cleaning mode.

A) The TrioPure

will shut off power to the salt chlo-

rinator when in Cleaning mode. If the

Chlorine

Control

display shows

longer than twenty-four

(24) hours, contact our telephone support number,

800.676.1335 ext. 293, for service.

Figure 32

Figure 33

Figure 34

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды