Del ozone TrioPure 25 Скачать руководство пользователя страница 4

Страница: 4 / 31

ADDENDUM FOR CANADIAN TRIOPURE INSTALLATIONS

The following information is for Canadian installations of the TrioPure and takes precedence over other information

in the manual.

WARNING: Heavy pool (or spa) usage and higher temperatures may require higher chlorine output to maintain

proper free available chlorine residuals.

When replacing the cell, only use replacement cells having a label that clearly states that it is a replacement cell

for the chlorine generating device TrioPure-25, REGISTRATION NUMBER 28566,

PEST CONTROL PRODUCTS ACT

DO NOT add pool/spa chemicals directly to the skimmer. This may damage the

chlo

rinator cell.

Maintaining high salt and chlorine levels above recommended range can contribute to corrosion of pool and

spa equipment.

Check the expiry date of the test kit. Test results may be inaccurate if used after expiry date.

WARNING: To reduce the risk of injury, do not permit children to operate this device.

Follow all aspects of the local and National Electrical Code(s) when installing the TrioPure-25.

With high bather loads or high temperatures, the pool owner may add “liquid chlorine” with the active

ingredient of Sodium Hypochlorite to supplement the Chlorine production in the TrioPure-25.

When properly maintained and cleaned and under normal use conditions, the life expectancy of the chlorinator

cell and electrodes is three years minimum - approximately 15, 000 hours of operation.

10. NOTE: For outdoor pools, chlorine residual can be protected from destruction by sun’s rays by addition of

cyanuric acid stabilizer. See Section 5 of the manual for recommended cyanuric acid levels.

11. When the TrioPure is used to sanitize a pool and spa combination, the spa must be completely drained

periodically. The number of days between COMPLETE SPA DRAINAGE is equal to the volume of spa water in

liters, divided by 10 times the maximum number of daily spa users. Refill spa with water. Repeat DIRECTIONS

FOR USE of the device.

12. Pool Capacity:

• TrioPure-25: Up to 57,000 liters (15,000 gallons)

Swimming pool

Free available Chlorine

1.0 - 3.0 ppm

7.2 - 7.8

Total alkalinity

100 - 120 ppm

Calcium hardness

200 - 300 ppm

Salt

3000-5000 ppm

Health and Hyperthermia warnings for spa devices:

• People with a medical condition should consult a physician before entering pool or spa water.
• Maximum spa water usage temperature is 40°C. Bathing in spa water at 40°C should not exceed 15 minutes.

TrioPure

Sanitation System

Maintain daily levels as determined by testing kit.

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды