Del ozone TrioPure 25 Скачать руководство пользователя страница 8

Страница: 8 / 31

SECTION 2

Installation (Continued)

2D Mounting the TrioPure

IMPORTANT:

A qualified swimming pool professional and certi

fied electrician must install the TrioPure

Sanitation System.

Refer to local building codes for any additional requirements.

If you need assistance in finding a qualified installer, please

contact our customer service department at 1-800-676-1335,

ext. 293, or visit www.delozone.com.

Step 1 - Before starting, pick a mounting location that:

•

Is 3 m (10 ft.) ft. minimum from the edge of pool

•

Allows space for ease of plumbing and electrical installa-

tion. Review

Sections 2E & 2F

•

The bottom of the

TrioPure

has a minimum clearance

of 0.6 m (2 ft.) from all obstacles for ease of visibility and

maintenance. Space must be allowed on all sides of the

enclosure for adequate ventilation and to allow the clear

cover to open completely.

•

Sufficient clearance on top and both sides for your

TrioPure

for plumbing and electrical hardware access.

•

The top of the

TrioPure

is no higher than 2.4 m (8 ft.) above

or lower than 1 m (3 ft.) below the water surface.

•

••

Avoid installing your

TrioPure

above any heat generating

source such as a heater or pump.

•

Meets the guidelines in

Section 2E

(Plumbing) and

Sec-

tion 2F

(Electrical) in this manual

•

It is recommended that the TrioPure is mounted with

¼-20 galvanized hex bolts. The bolt mounting pattern

is 254 mm (10 in.) wide by 375 mm (14.75 ft.) high.

Screw in bottom bolts so that the head is 6.3 mm (¼

in.) from the mounting surface. Slide the TrioPure onto

these bolts and screw the upper bolts through the top

mounting holes on the enclosure.

Note:

If installing your TrioPure

below water level, an addi-

tional light-duty check valve is required after the chlorinator

cell to prevent backwash in the unlikely event of ozone check

valve failure while the unit has been powered down.

Step 2

- Level and mount the TrioPure

on a wall or a post.

If mounting the TrioPure

on a post, it must be centered on

a flat panel of waterproof material at least 457 mm x 610

mm (18” x 24”). Do not enclose the TrioPure

in any box. Do

not install it above any heat source. Install the TrioPure

minimum of 3m (10’ ft.) from the pool edge. Do not install

the TrioPure in direct sunlight. In locations where the daytime

temperatures regularly exceed 37ºC (100º F), the internal

thermal protection switch may shut down the TrioPure. When

the temperature drops the TrioPure power will be restored.

2E Plumbing

2e-1 Installing the TrioPure

Manifold

Note:

Turn off main pool pump and disconnect power before

installing the bypass manifold.
There are many different types of pool construction and pool

equipment configurations. The following pool configuration list

will help you determine which way to plumb your TrioPure

for

optimal performance. Each configuration has an easy to plumb

illustration for installing the bypass manifold.

NOTE:

The bypass manifold must be mounted horizontally to

prevent bubbles from returning to the TrioPure

pump and

tripping the flow switch

TrioPure

Sanitation System

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

Before installing the TrioPure

bypass manifold, determine

whether your pool is a:

New Pool (can I plumb a dedicated 2 cm (¾”) return)

Existing Pool (returns already in place)

Pool Only

Pool/Spa combination

Also, determine whether your have an

In-Floor Cleaning System

(ICS) or

Solar Heater

installed in your existing pool (or plan to

install one on your new pool).
The plumbing diagrams shown on the following pages are

schematic representations of the various pool configurations

and plumbing lengths are for reference only.

2e-2 Plumbing Configuration Chart

If your pool is:

New Pool

Pool Only

No ICS

No Solar / Solar -

See Figure 1

If your pool is:

Existing Pool

Pool Only

No ICS

No Solar / Solar -

See Figure 2

If your pool is:

Existing Pool

Pool Only

ICS

No Solar / Solar -

See Figure 3

If your pool is:

New Pool

Pool Spa Combo

No ICS

No Solar -

See Figure 4

If your pool is:

Existing Pool

Pool Spa Combo

No ICS

No Solar -

See Figure 5

If your pool is:

Existing Pool

Pool Spa Combo

ICS

No Solar -

See Figure 6

If your pool is:

New Pool

Pool Spa Combo

No ICS

Solar -

See Figure 7

If your pool is:

Existing Pool

Pool Spa Combo

No ICS

Solar -

See Figure 8

If your pool is:

Existing Pool

Pool Spa Combo

ICS

Solar -

See Figure 9

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды