Del ozone TrioPure 25 Скачать руководство пользователя страница 7

Страница: 7 / 31

2A Verify Contents

Inspect your TrioPure

shipping box for the following items:

(1) TrioPure-25 with salt chlorinator cell attached
(1) Molded plastic bypass installation manifold
(1) 3.0 A fuse for 120 V & 1.5 A fuse for 240 V (in bag near TB1

Terminal Block)

(1) Manual
(1) Quick Reference Guide

2B Installation Tips

CAUTION:

The bypass manifold must be correctly installed or

your

TrioPure

system will not work properly and the warranty will

be voided. The bypass manifold contains two check valves that

are matched to create the correct backpressure and anti-siphon
protection for optimum performance of your

TrioPure

•

The TrioPure

sanitation system should be installed on resi-

dential pools only. The salt level in your TrioPure

pool should

be between 3,000 and 5,000 ppm (3,500 recommended).

•

If you use solar panels for pool heating, your TrioPure

must

be plumbed with the manifold before the solar heater, and

the water return from the TrioPure

after solar heater. The

bubbles that can be created through your solar heater can

inadvertently shut off the TrioPure-25. See Figures 1, 2, 3,

7, 8 and 9.

•

The TrioPure

must be installed no more than 2.4 m (8 ft.)

above water level or no more than 1 m (3 ft.) (measured from

the top of the enclosure) below water level to maintain the

correct pressure and flow characteristics for optimum opera

tion of the unit.

•

DO NOT

USE

copper or iron piping for the TrioPure

installa-

tion as chlorine and ozone have corrosive effects. Consult

your pool professional for appropriate pool equipment piping

materials.

•

Even though the TrioPure

is designed for outdoor use, care

should be taken when choosing a mounting location. To

protect your investment, mount the TrioPure

where it is

protected from the elements (i.e., direct sun, rain, dirt, sprin-

klers) and completely sheltered if possible while providing

adequate ventilation.

•

If ozone bubbles are not desirable (for indoor pools, vinyl-lined

pools, pools with covers, negative edge pools, etc.), the addition

of a DEL Ozone Mixing-Degas Vessel (MDV-30) is recommended.

Contact your local pool equipment dealer or visit DEL Ozone’s

website at www.delozone.com to find one near you.

SECTION 2

Installation

The most common pool and pool/spa configurations are
discussed in this manual. For questions on your specific

installation, please contact DEL Ozone at 800-676-1335,
extension 293.

TrioPure

Sanitation System

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

•

“

Salt & Pepper” fittings, eyeball fittings, or the use of a grav

ity drains as return lines are recommended since they can

better mix and disperse treated pool water.

•

Plumb the TrioPure

to the bypass manifold using a

minimum amount of plumbing fittings. This minimizes

backpressure.

•

The TrioPure

has been designed with an electronic water

flow switch. This device automatically shuts down both the

salt chlorinator and ozone subsystems when the water flow

through the TrioPure

is interrupted. To prevent personal

injury and damage to the TrioPure

salt chlorinator cell, do

not interfere with this system in any way. It is designed for

your protection and the protection of the TrioPure

•

Always check the salt chlorinator cell frequently for the

accumulation of pool debris that may have bypassed the

pool filter. This can affect the operation of the flow switch,

ozone injector, pump, and salt chlorinator plates.

•

Salt is not lost through evaporation, but is lost when water is

splashed out of the pool or during backwashing. Rainfall or

adding fresh water dilutes the salt concentration and you will

need to occasionally add more salt to the swimming pool. Check

salinity level before and after adding additional salt.

•

If the TrioPure

is being installed on a new pool, do not add

salt for 2 weeks after the pool has been filled. This protects

plaster from staining and allows the finish to cure.

•

Pool water with high calcium levels, or hard water,

can cause excessive calcification [scale] in the Chlo

rinator Cell. Installation of a T-filter or Y-filter trap

with a 60-mesh screen near the Water Out line of the

TrioPure, along with frequent acid cleaning of the cell

plates [reference Section 5d-2: Chlorinator Cell Plate

Cleaning] will reduce water hardness over time. The

monthly addition of a non-chlorine shock (Potassium

Monopersulfate or equivalent) to the pool will keep

the scale soft, preventing the filter trap from clogging.
Remove and clean the filter trap as necessay.

2-C Recommended Installation

Materials

•

Liquid tight conduit, connectors & junction box, and appro-

priately sized and rated wire per local electrical codes.

Note:

The TrioPure is designed for 1.5 cm (1/2”) NPT liquid

tight fittings

•

Two 5 cm (2”) unions for manifold installation to pool return

line (use reducer bushings for 3 cm (1½”)).

•

2 cm (3/4”) unions, ball-valves, and rigid PVC or Spa-Flex

tubing for installation from manifold to TrioPure

•

Mounting hardware for securing TrioPure

to a stable sur-

face (wall, fence, post with backboard) sufficient to support

the unit.

Note:

If you are mounting the TrioPure

to the side of house

wall that is located near a bedroom, consider using a vibra-

tion dampening material to reduce vibration noise.

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды