Del ozone TrioPure 25 Скачать руководство пользователя страница 25

Страница: 25 / 31

TrioPure

Sanitation System

SECTION 6

Troubleshooting

6A Troubleshooting the TrioPure

Problem

Cause(s)

Solution(s)

High Salt Indicator LED is Flashing

A) The TrioPure

has

detected a possible

high salt condition.

A) Check the salt level (salinity) of the pool water with

a test strip or digital meter. Never dilute the pool water

without verifying the salt level with a digital meter or test

strip first. If the salt level is over 5,000 ppm, then add

fresh water, run the pool pump for 24 hours, then check

the salt level again. Repeat as needed to reduce the salt

level to within 3,000 to 5,000 ppm.

Note:

Water must be

pumped out of the pool before fresh water can be added

to dilute the pool.

B) There is excessive

scale build-up or debris

on the chlorinator cell

plates.

B) If the tested salt level is within specified limits, check

the chlorinator cell plates for scale formation or debris

caught between the plates. Clean as required (refer

to Section 5d-3).

Note:

High Salt Indicator may flash

momentarily when adjusting the Chlorine Control.

Low Salt Indicator LED is Flashing

A) The TrioPure

has

detected a possible low

salt condition.

A) Check the salt level (salinity) of the pool water with a

test strip or digital meter. Never add salt to the pool with-

out verifying the salt level. If the salt level is below 3,000

ppm, then add salt (refer to

Section 3 - 3H ‘When to Add

Salt’ on page 12

), run the pool pump for 24 hours, then

check the salt level again. Repeat as needed to bring

the salt level to within 3,000 to 5,000 ppm.

B) Low Water Temp.

B) Check the pool temperature. If the pool water tem-

perature is low, combinations of low temperature and/or

Chlorine Control

setting can cause the Low Salt LED

indicator to flash.

C) Low Power Setting.

C) If

Chlorine Control

knob setting is set too low

(from

“

”

“4”

), then disregard the

Low Salt

indica-

tor. Combinations of low temperature and/or

Chlorine

Control

setting can cause the

Low Salt

LED indicator

to flash.

Ozone Production Cell Indicators Turn Red (O3 Cell 1–O3- Cell 2 for TrioPure-25)

A) Insufficient water

flow.

A) If the

Water Flow

indicator is red, there is insuf-

ficient water flow, which causes the

TrioPure

to turn off

all ozone cells. Correct the water flow problem before

further troubleshooting.

B) The ozone CD cell

has a blown fuse.

B) With power off to the unit, open the enclosure, remove

the front panel and examine fuse – replace as neces-

sary, then close up the TrioPure

and restore power.

C) There is a faulty

ozone power supply.

C) If replacement fuse blows (indicator goes red) on

power up, replace the ozone cell. Call for service. The

TrioPure

will continue to work with the remaining

ozone CD cells.

Figure 29

Figure 30

Figure 31

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды