Del ozone TrioPure 25 Скачать руководство пользователя страница 21

Страница: 21 / 31

TrioPure

Sanitation System

5A Front Panel Diagnostics

The front panel of the

TrioPure

contains diagnostics and feed-

back displays to let you know how the system is operating and

whether there is a problem with the system. Familiarize yourself

with the following diagnostic readouts and functions:

SECTION 5

Monitoring & Maintenance

•

Chlorine Production

Normal Indicator Messages

= Chlorine Control turned off

1-10

= Level of chlorine production

= Chlorinator plates are in “clean mode” (down time

between polarity changes)
Error Indicator Messages (refer to Section 6A, Trouble-

shooting, Page 20)

= Chlorinator shut off due to problem

= Current over limit

•

Chlorine Control

The

Chlorine Control Knob

controls the level of chlo-

rine production. Turn the knob clockwise to increase the

amount of chlorine in the pool and counterclockwise to

decrease the amount of chlorine in the pool.

•

Low Salt Indicator

The

Low Salt

indicator is normally off and not lit.

The

Low Salt

indicator blinks red when the pool should

be checked for low salinity (

Warning

-always check salinity

level with a test strip or digital meter before adding

additional salt).

•

High Salt Indicator

The

High Salt

indicator is normally off and not lit.

The

High Salt

indicator blinks red when the pool should be

checked for high salinity. (

Warning

-always check salinity

level with a test strip or digital meter before diluting water).

•

Ozone Production Indicators

The normal operating color of the TrioPure’s

Ozone Cell

LED indicators is green.

A red LED indicates that the

Ozone Cell

is not operating

(refer to Section 6A, Troubleshooting, Page 20).
The TrioPure-25 has two LEDs.

Note:

During normal

operation, ozone cells do not function if the water flow

indicator is RED.

•

Water Flow Indicator

The

Water Flow

LED indicator is normally green.

A red

Water Flow

LED indicates insufficient water flow.

Note:

When water flow is interrupted, both chlorine and

ozone production is halted. A

error is displayed.

•

Water Temperature Indicator

The

Water Temperature

LED indicator is normally

green

(water between 15 and 40°C (59-104˚F)).

A red

Water Temperature

LED indicates water

temperature is either too low or high.

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

5b-1 Chlorine Level Requirements

During peak sanitizer demand (rainy season, heavy bather

load, wind storms, high temperatures, etc.), it may be neces-

sary to increase your sanitizer level by increasing the Chlorine

Control level setting. Conversely, during low sanitizer demand,

you can decrease your Chlorinator Control level to a lower set-

ting. For extremely heavy sanitizer demand, supplement with

a Potassium Monopersulfate (non-chlorine) based shock.

WARNING:

During cold-water conditions, sanitizer demand

is reduced significantly. For colder climate regions with sus

tained low or freezing temperatures, contact your local pool

professional for proper pool winterizing instructions.

WARNING:

Excessive chlorine levels can cause corrosion

damage to swimming pool rails, ladders, heater heat exchang-

ers, light faceplates and other metallic equipment. Avoid over

saturation of chlorine levels.

5b-2 pH Level:

When pH levels fall below the recommended range, sanitizer

is used more quickly and can damage equipment. For

pH levels higher than the recommended range, sanitizer

becomes less effective. Improper pH also contributes to the

strong smell, red eyes, dry itchy skin and brittle hair conditions

associated with “too much chlorine”.

5B Water Chemistry Parameters

VERY IMPORTANT NOTE!

Your TrioPure

is designed to

provide continuous sanitation. We recommend the following

water chemistry ranges and periodic checks to monitor your

systems efficiency.

Free available chlorine

1.0-3.0 ppm

7.2-7.8

Total alkalinity

100-120 ppm

Calcium hardness

200-300 ppm

Salt level (Salinity)

3,000-5,000 ppm

Cyanuric acid

30-100 ppm

Visual

Chlorinator Cell

Inspection:

Ozone production

(bubbles at the

injector).

Inspect for the build-up of

calcium on the plates.

WEEKLY CHECKS

SWIMMING POOL

Maintain daily levels as determined by testing kit.

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды