Del ozone TrioPure 25 Скачать руководство пользователя страница 27

Страница: 27 / 31

Cause(s)

Solution(s)

Chlorine Production

display reads

A) The Salt Chlorina-

tor plates have scale

build-up.

A) Look through the salt chlorinator cell, checking for any

white scale build-up on the plates. If scale build-up

is found, clean the chlorinator cell plates per

Section

5d-3

, page 18, of this manual. Check and balance

pool chemistry as required after cleaning.

B) The Salt Chlorinator

plates are shorting out

due to a foreign object

lodged in the cell.

B) Look through the salt chlorinator cell, checking for

any object that may have gotten through the filter and

become stuck in the salt chlorinator plates (i.e., hair-

pin, paper clip, etc.). Contact our telephone support

number, 800.676.1335 ext. 293, for service.

C) Cell terminals have

become loose, discon-

nected, or corroded.

C) Tighten, reconnect, or clean as necessary.

Chlorine Production

display will not read all the way to 10

A) Pool water low salin-

ity, low temperature,

or calcium buildup on

the chlorinator cell

are restricting the

amount of current

drawn at the chlori-

nator cel

A) Check the pool salt level (salinity) and water tem-

perature. If either level is low this may affect the

amount of chlorine production. If the tested free

chlorine level is too low or if the pool shows signs

of insufficient chlorine production (algae or chlorine

smell) in the pool water, you may increase the salin-

ity slightly in order to make the TrioPure

produce

more chlorine. Add salt in small 12 to 23 kg (25-

50 pounds) increments and allow 24 hours for the

salt to dissolve before taking the next reading and

making any more adjustments. Always keep the

salinity below 5,000 ppm. If there is scale buildup,

clean chlorinator cell per

Section 5-d3.

Indicator lights on front panel are not on.

A) The TrioPure

switched off.

A) Open the TrioPure

and turn the power switch on.

B) The TrioPure

is not

getting power.

B) Check main pool circuit breaker.

C) Main breaker is off.

C) Check main breaker.

D) Main fuse is blown.

D) Check main fuse and replace if necessary. Note: A

blown fuse can be caused by excessive salt levels

above 5,000 ppm with the

Chlorine Control

knob

set to full power (10).

TrioPure

Sanitation System

Figure 35

Figure 36

Figure 37

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

Содержание TrioPure 25
































Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды

Del ozone TrioPure 25, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TrioPure 25

Отзывы:

Похожие инструкции для TrioPure 25

Бренды по названию

Популярные бренды