Del ozone TrioPure 25 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 31

background image

8

TrioPure

TM

Sanitation System

2e-3 Plumbing Configurations (Continued)

Figure 9 -

(Existing Pool, Pool Spa Combination, ICS, Solar):

· Manifold to be plumbed between the filter and heater.

· TrioPure

TM

return port of the bypass manifold capped off.

· Return from TrioPure

TM

plumbed to the line of the ICS that goes to the lowest point of the pool.

- This is after the ICS diverter valve.

- A light duty check valve must be placed between the diverter valve and the point where TrioPure

TM

enters the ICS line.

· An automated shut-off valve needs to be put in the line between the bypass manifold and the TrioPure

TM

, which is tied into

the Pool/Spa control system, and shuts off water to the TrioPure when in spa mode.

- If this is overlooked, the TrioPure

TM

will pump water from the spa into the pool, when in spa mode.

· Del recommends installing 2 cm (¾”) ball valves on the inlet and outlet of the Triopure to facilitate Salt Cell removal for

cleaning and a ball valve after the Bypass Manifold to control water flow through the Salt Cell.

Special Note about Spillway Valves on Pool/Spa Combinations without Solar.

If a spillway valve is used, the line which takes water

from the pool into the spa creating the overflow effect, it must be equipped with a light duty check valve to prevent water from being

diverted back into the pool, when in spa mode, and any lines to or from the TrioPure must be plumbed after it.

J

A

J

ICS

POOL

J

SPA

SOLAR

HEATER

TrioPure

TM

DEL Ozone · San Luis Obispo, CA 93401 · USA · 800-676-1335 · Fax: 805-541-8459

«
...
11
12
13
14
15
...
»

Содержание TrioPure 25
































Отзывы:

Нет отзывов

Похожие инструкции для TrioPure 25

Бренд: Galcon Страницы: 20

Бренд: SPIDO Страницы: 24

Бренд: Serenity Страницы: 3

HOF14AFRQ 1F Series

Бренд: Halsey Taylor Страницы: 4

PUR-Gas MCTG-0050

Бренд: Matheson Страницы: 16

Бренд: RAFTEC Страницы: 28

Бренд: Plymovent Страницы: 20

Бренд: Balboa Страницы: 7

Бренд: T.I.P. Страницы: 44

Бренд: Hamilton Beach Страницы: 100

Бренд: CPF Страницы: 8

Бренд: GE Страницы: 3

SmartWater GNUL30Z

Бренд: GE Страницы: 9

SmartWater GNWH08C

Бренд: GE Страницы: 4

SmartWater GXRM10

Бренд: GE Страницы: 6

SmartWater FX12M

Бренд: GE Страницы: 2

SmartWater FX12P

Бренд: GE Страницы: 2

SmartWater GXITQ

Бренд: GE Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды