DBL Technology GoIP Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 63

background image

GoIP User Manual

http://www.dbltek.com

61

Appendix E.

CID Call Forward

For incoming GSM calls, the phone number of the caller can be displayed at the called party (SIP terminal).
The device supports the following two methods.

Unfortunately, not all SIP servers support one or both

methods.

Please check with the vendor of the SIP server for more information.

1. Remote Party ID - This is a parameter in a SIP INVITE message.

Choose this if both SIP Server and SIP

terminal support this parameter.

Example: Caller ID / number = 13800000000
The Remote Party ID parameter is included in the SIP INVITE Message below.

2. USD CID as SIP Caller number - This parameter specifies the use of GSM Caller ID instead of its SIP

number in the INVITE message when making a call.

Please make sure that the SIP server supports this

type of INVITE message since the call now is not originated from a valid SIP number defined in the server.
Please note that the Remote-Party-ID is also included in the INVITE message.

«
...
60
61
62
63
»

Содержание GoIP
































































Отзывы:

Нет отзывов

Похожие инструкции для GoIP

Бренд: Vanguard Страницы: 74

Бренд: NeoGate Страницы: 37

Бренд: Elvaco Страницы: 2

Codian GW 3201 Series

Бренд: TANDBERG Страницы: 18

Pathport OCTO 64 Series

Бренд: Pathway connectivity solutions Страницы: 70

Anybus Modbus-TCP/RTU Gateway

Бренд: HMS Страницы: 20

Бренд: Sharp Страницы: 16

Бренд: Vaisala Страницы: 32

Бренд: Vaillant Страницы: 40

AirLink RV50 Series

Бренд: Sierra Wireless Страницы: 78

Бренд: HD Страницы: 2

Dolphin USB 500T

Бренд: EnOcean Страницы: 11

Бренд: ZyXEL Communications Страницы: 10

Бренд: Schlage Страницы: 60

Бренд: GL-INET Страницы: 2

Бренд: 2N Страницы: 35

Бренд: dresden elektronik Страницы: 14

Touchstone DG6450

Бренд: CommScope Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды