DBL Technology GoIP Скачать руководство пользователя страница 7

Страница: 7 / 63

GoIP User Manual

http://www.dbltek.com

AC/DC Power Adapter:



GoIP1: 12V/500mA



GoIP4: 12V/2A



GoIP8: 12V/3A



GoIP16: 12V/4A



GoIP32: 12V/4.5A

1 x Ethernet CAT5 Cable (2M)

1.6

LED Indicators

LED indicators (shown above for GoIP-8) are used to show the current status of the device.

They are often used

to determine if the GoIP is working normally or not.

LED Label

Description

Power

This LED is red and illuminates when power is connected.

LAN

This LED is red and illuminates when the LAN port is connected and blinks when data
transmission occurs.

This LED is red and illuminates when the PC port is connected and blinks when data
transmission occurs.

RUN

This LED is green and blinks at a rate of every 100ms when VoIP is not ready for
making calls. (Fast Blink)
It blinks at a rate of every second when VoIP is ready for making calls (Slow Blink).

Содержание GoIP
































































Результаты поиска

Содержание GoIP

Отзывы:

Похожие инструкции для GoIP

Бренды по названию

Популярные бренды

DBL Technology GoIP, Руководство пользователя

Результаты поиска

Содержание GoIP

Отзывы:

Похожие инструкции для GoIP

Бренды по названию

Популярные бренды