DBL Technology GoIP Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 63

background image

GoIP User Manual

http://www.dbltek.com

24

4. Trunk Gateway Mode (for all models except GoIP-1)

This mode offers a seamless interface with the SIP Trunk configuration in a SIP server.

In general, SIP

registration is not required in this mode; this is an advantage for a SIP system that requires a license per
registration.

If SIP server and the device are not in the same network segment, it is recommended that

both SIP server and the device are using public IPs for reliable operation.

Installing either one or both

(SIP server and the device) behind NAT may or may not work properly depending on the SIP Server and
the routers (on each side) as well.

In this case, SIP server must support NAT.

Some routers may map an

internal port to a different external port number.

Otherwise, VoIP calls may fail to establish properly in

this network environment.

The device accepts calls from up to 3 IP addresses (SIP Trunk Gateway1, SIP Trunk Gateway2, SIP Trunk

«
...
23
24
25
26
27
...
»

Содержание GoIP
































































Отзывы:

Нет отзывов

Похожие инструкции для GoIP

MultiVOIP MVP210-SS

Бренд: Multitech Страницы: 36

Бренд: XAVI Technologies Corp. Страницы: 51

Бренд: ZyXEL Communications Страницы: 6

Бренд: Nokia Страницы: 107

Бренд: Toshiba Страницы: 99

Бренд: VBOX Страницы: 11

RouteFinder RF550VPN

Бренд: Multi-Tech Страницы: 76

Envoy Communications Gateway

Бренд: enphase Страницы: 100

Бренд: SELECTRONIX Страницы: 28

Бренд: AMX Страницы: 2

NetLinx Clear Connect NXB-CCG

Бренд: AMX Страницы: 3

NetLinx NXB-KNX

Бренд: AMX Страницы: 2

Бренд: Hybertone Страницы: 4

Бренд: Hybertone Страницы: 34

Бренд: Iseo Страницы: 7

Бренд: Viola Systems Страницы: 37

Бренд: Viola Systems Страницы: 36

Бренд: TECOM Страницы: 139

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды