DBL Technology GoIP Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 63

background image

GoIP User Manual

http://www.dbltek.com

50

The procedures to send an USSD command are:
a) Select the Line (GSM channel) that you want to send an USSD command to the service provider.

The line status and the SIM (GSM) number are displayed.

The last option "All Lines" means that all

channels are selected and the same USSD command is sent via all channels provided that they are in
the Login Status.

b) Enter the USSD command
c) Click [Send].

Example:

For the service provider PCCW in Hong Kong, the USSD command to check balance is ##122#.

Enter

“##122#” and the click [Start]. The following screen is then displayed.

A few seconds later, the service provider sends back a USSD message/response as shown below.

Click [Back] to return to the Send USSD command page.
For certain service requests, user responses are required.

Just following USSD message and then send

back a response via SEND USSD command.

3.4.4Send SMS

Click [Send SMS] to access the Send SMS webpage as shown below

«
...
49
50
51
52
53
...
»

Содержание GoIP
































































Отзывы:

Нет отзывов

Похожие инструкции для GoIP

Бренд: ICP DAS USA Страницы: 7

Бренд: ICP DAS USA Страницы: 4

Бренд: Ubee Страницы: 114

Бренд: Ubee Страницы: 105

Бренд: Ubee Страницы: 96

Бренд: Ubee Страницы: 96

Бренд: Bticino Страницы: 4

Бренд: SmartRG Страницы: 122

Бренд: MIKRODEV Страницы: 12

Бренд: ioLIVING Страницы: 13

Fieldgate PAM SFG600

Бренд: Endress+Hauser Страницы: 20

Бренд: ATX Страницы: 30

Бренд: ATX Страницы: 32

Бренд: Rosslare Страницы: 30

Бренд: Weinzierl Страницы: 49

Бренд: Ackcio Страницы: 19

Бренд: Sonoff Страницы: 2

Бренд: RTA Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды