DBL Technology GoIP Скачать руководство пользователя страница 44

Страница: 44 / 63

GoIP User Manual

http://www.dbltek.com

Unconditional Call

Forward



Forward Num

Forward all incoming calls unconditionally to the number specified.

This specifies the phone number to receive forwarded calls under this
condition.

Not Set

Call Forward Busy



Forward Num

Forward calls when the GSM Channel is in use.
This specifies the phone number to receive forwarded calls under this
condition.

Not Set

Call Forward No

Answer



Forward Num

Forward the call when an incoming call is not answered.

This specifies the phone number to receive forwarded calls under this
condition.

Not Set

Call Forward

Unreachable



Forward Num

Forward calls when the GSM channel cannot register to the carrier.

This specifies the phone number to receive forwarded calls under this
condition.

Not Set

3.3.13 IMEI

This section allows IMEI modifications for all Channel in a single page.

At the bottom of the IMEI list, user can

also enable an option to change the IMEI of each channel automatically at an interval defined by the Change
Period.

The minimum Change Period allowed is 10 minutes which is currently set as the default value.

Changing

IMEI only occurs when the channel is idle.

When it occurs, the GSM channel drops its current registration and

then use the new IMEI to register to the network.

Содержание GoIP
































































Результаты поиска

Содержание GoIP

Отзывы:

Похожие инструкции для GoIP

Бренды по названию

Популярные бренды

DBL Technology GoIP, Руководство пользователя

Результаты поиска

Содержание GoIP

Отзывы:

Похожие инструкции для GoIP

Бренды по названию

Популярные бренды