DBL Technology GoIP Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 63

background image

GoIP User Manual

http://www.dbltek.com

42

10. Billing Increment (s)

This is a call duration measurement unit expressed in seconds. Depending
on your service provider, some services are measured and billed in sixty
second increments (one minute) or the billing increment may be in
durations of six or even ten seconds.

11. SMS Alert Number

This specifies the GSM number to receive a SMS Alert on the Total Talk
Time. If this parameter is blank, no SMS Alert will be sent.

12. SMS Alert ID

This parameter is used to identify the channel sending the SMS Alert.

13. SMS Alert Trigger

(Remain Talk Time (m))

The Remain Time is the Total Talk Time Limit minus the total talk time
used.

When this Remain Time reaches the value set in the parameter, a

SMS Alert is sent to the SMS Alert Number automatically.

14. Hide My GSM Number

This parameter determines if the caller party can receive the phone
number of the caller or not.

Enabling this parameter hides My GSM

number from the called party.

This specified if the phone number of the caller is shown at the called
party or not.

3.3.12 SIM Forward

This section allows the user to define the GSM Call Forward settings for each channel.

There are four Call

Forward conditions:
1. Always - Forward all incoming calls unconditionally
2. Busy - Forward all incoming calls when busy.
3. No Answer - Forward the incoming calls when it is not answered.
4. No Service - Forward all incoming calls when the SIM cannot register to the network.

There are 3 choices for each Call Forward condition.

1. Set - This enable the Call Forward function.

This setting is sent to the network whenever the SIM is

starting a new registration to the network.

2. Disable - This disable the Call Forward function. This setting is sent to the network whenever the SIM is

starting a new registration to the network.

3. Not Set - This leaves the current SIM Call Forward setting in the network unchanged. This setting is NOT

sent to the network at all.

Parameter
(SIM Forward)

Description

Default Value

«
...
41
42
43
44
45
...
»

Содержание GoIP
































































Отзывы:

Нет отзывов

Похожие инструкции для GoIP

Бренд: XAVI Technologies Corp. Страницы: 51

Бренд: Deb Страницы: 4

Бренд: Seneca Страницы: 22

EKI-1200-CE Series

Бренд: Advantech Страницы: 67

Flight Stream 110/210

Бренд: Garmin Страницы: 46

Бренд: ioSelect Страницы: 160

Бренд: RTA Страницы: 74

Бренд: MikroTik Страницы: 22

Бренд: ICP DAS USA Страницы: 122

Бренд: 3Com Страницы: 112

Бренд: L&S Страницы: 28

Бренд: Plasmatronics Страницы: 2

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 8

Бренд: Planet Networking & Communication Страницы: 73

Бренд: AirLive Страницы: 272

Бренд: THOMSON Страницы: 98

Бренд: Gigalink Страницы: 45

Бренд: OpenVox Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды