Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 45

Страница: 45 / 83

S/5 Airway modules

Document No. 800 1005-1

Patient spirometry option

•

Switch the monitor off and install the PVX board, then switch the monitor back on.

•

Preset gas measurement settings:

Airway Gas - Spirometry Setup - Paw Scale - 20

Flow Scale - 15

Check that the patient spirometry connectors on the front panel are clean and intact.

Connect a clean spirometry tube to the module and a clean D-lite to the other end of the

tube. Block the D-lite’s sampling line port, for example with a luer stopper.

Take the D-lite into your hand and occlude both ends tightly with your fingers (or with both

hands). Pressing firmly with the fingers creates a pressure inside the D-lite. Check that a

pressure of at least 5 cmH

O is generated.

NOTE: If the module has the male & female patient spirometry connectors (pediatric

option), make sure that the date marking on the D-lite is 10/94 or newer.

If the system leaks heavily, no pressure will be generated.

If there is a small leak in the connections, the monitor will measure a pressure difference

which is then interpreted as flow and seen on the monitor screen. The pressure waveform

decreases slowly and the flow waveform either goes above, or below the zero line,

depending on which of the connectors leaks.

In case of leakage, check all connections and try again.

Remove the blockage from the sampling line port and connect the sampling line. Breath

through the wider side of the D-lite. Check that the flow waveform moves downwards when

you breath in, and upwards when you breath out.

If the flow waveform moves in opposite manner, check the order of the PVX tubes inside the

module.

If possible, check the patient spirometry measurement also with the spirometry tester (order

code 884202). Follow the instructions that are supplied with the tester.

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды