Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 83

background image

S/5 Airway modules

Document No. 800 1005-1

47

4

TROUBLESHOOTING

4.1

Troubleshooting chart

Trouble

Possible Cause/Treatment

No response to breathing

Sampling line or water trap blocked or loose, or improperly attached.
Water trap container full.
Interface cable to monitor disconnected.
See chapter “

Gas sampling system troubleshooting

.”

SENSOR INOP. message

The temperature is too high, check fan and filter at the rear panel.
Communication error, check timeout and bad checksum values at the service menu.
Check Airway Module connection cable and supply voltages.
Check ACX measuring board.

xx ZEROING ERROR-message

Gas zeroing failed. Condensation or residual gases are affecting zero measurement. Allow module to run
drawing room air for half an hour and calibrate again.

AIR LEAK-message

Air leak in sampling system. Probably water trap or the sampling line is not attached properly. Gas zero
valve failure. Pump failure or gas outlet blockage. Supply voltage missing

REPLACE TRAP-message

Flow resistance increased due to residue built-up on water trap membrane. Replace the water trap.

REBREATHING-message

CO

2

concentration in inspiratory air is too high. Possibly CO

2

absorber in ventilator is saturated. Change

the absorber.

OCCLUSION-message

Sampling line or water trap is occluded. Water trap container is full. If occlusion persists check internal
tubing for blockages. Check the power supply voltages.

SELECT AGENT-message

No anesthetic agent is selected though delivery is started. Vaporizer valve is broken. Traces of cleaning or
disinfecting agent in the water trap container affecting the readouts. Replace the water trap.

No response to any gas

Sampling line, water trap, or internal tubing blocked or loose, or improperly attached.
Pressure valve malfunction. Pump failure. Supply voltage missing. Serial communication error. Check
those items.

Sudden increase in gas display

Measuring chamber contamination.

±

15 V supply voltages missing.

Water trap malfunction. Check all internal tubing and the interior of the water trap for occlusions or leaks.
Replace water trap.
Check flow rates.

Abnormally high response to all
gases (or abnormally low) or
sudden occlusion warning

Pressure transducer failure. Exchange the ACX Measuring board.

Random output (resembling
noise)

Chopper motor timing pulses out of sync.
Chopper motor not running, motor faulty or connection loose.
Chopper motor driver transistor C-E open circuit or current limiter short circuit.
Exchange the ACX measuring board.

Strong drift in all gases

Leakage in the sampling line or internal tubing (especially in conjunction with too low readings).
Exchange the ACX measuring board.

No gas waveforms
intermittently.

Gas waveforms are not shown during automatic zeroing, occlusion, or air leak. Check the monitor screen
for possible messages and proceed accordingly.

«
...
51
52
53
54
55
...
»

Содержание S/5 B-GAS




















































































Отзывы:

Нет отзывов

Похожие инструкции для S/5 B-GAS

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Datavideo Страницы: 8

Бренд: L-Acoustics Страницы: 20

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: HQ Power Страницы: 23

Бренд: DSEGenset Страницы: 74

Бренд: ITALFARAD Страницы: 32

Бренд: AUMA Страницы: 24

Бренд: VALSTEAM ADCA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды