Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 40

Страница: 40 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

a) shorten the thick O

reference channel tube by 4 centimeters (the tube that is connected

to the upper part of the CO

absorber)

b) connect the OM ref. filter to the loose end of the tube

c) fasten the filter to the outermost hole in the tubing plate (at the PVX board side) with a

cable tie (order code 64001)

•

Replace the D-fend and the sampling line.

NOTE: Use only Datex-Ohmeda sampling lines in order to ensure proper functioning.

•

Connect the module to the Central Unit with a long gas interface cable and switch the

monitor on.

•

Configure the monitor screen so that all the needed parameters are shown, for example as

follows:

Monitor Setup

- Screen 1 Setup - Waveform Fields - Field 1 - Paw

Field 2 - Flow

Field 3 - Off

Field 4 - O2

Field 5 - AA

Field 6 - CO2

Digit Fields - Field 1 - Gases

Check that the module fan is running.

Wait until the message ‘Calibrating gas sensor’ disappears from the screen, then enter the

Service menu:

Monitor Setup

- Install/Service

(password 16-4-34)

- Service

(password 26-23-8)

Take down the information regarding Airway module software.

NOTE: The PVX software string does not appear into the ‘Sw version/Unit id’ -list. Check PVX

software from the sticker that is located on the PVX software EPROM (if the PVX board was

installed originally).

Enter the ACX service menu:

Parameters - Gas Unit - ACX

Check that the ‘Timeouts’, ‘Bad checksums’ and ‘Bad c-s by mod’ -values are not increasing

faster than by 50 per second. If one of the values is increasing faster, it indicates a failure in

module bus communication.

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды