Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 44

Страница: 44 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

Agent identification option

22.

Check that the ‘ACX_ASX Delay’ -value in the ACX service menu is within 400-800.

If the value is not within the range, readjust the flows and repeat the fall time measurement.

•

Enter the ASX service menu:

Gas Unit - ASX

NOTE: The ASX service menu values are not updated with the anesthetic identification unit

ASX-100.

23.

Feed calibration gas. When proper absorption spectrum is shown in the menu check that

the Peak normal value is close to 10.50 (±0.20). Check also that the difference between

the “Peak normal” and “Peak mirror” values is not higher than 0.30.

If the values do not meet the range, repeat the gas calibration.

•

Set the AA identification to the automatic mode:

Agents - Select Agent - Auto - Previous Menu

24.

Feed calibration gas (order code 755583) and check that the message 'Desflurane'

appears into the digit field for gases.

NOTE: The ASX-100 is not capable of identifying Desflurane.

NOTE: The ASX-100 with software 878364-1.1, or lower, is not capable of identifying

calibration gas R23 (order code 755582). Therefore, the message ‘Agent mixture’ should

appear instead.

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды