Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 56

Страница: 56 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

4.3

OM measuring unit troubleshooting

Because of the complex and very sensitive construction of the oxygen measuring unit no repairs

should be attempted inside the unit. Instead, if the fault has been found in the measuring unit

itself, it should be replaced and the faulty unit be sent to Datex-Ohmeda for repair.
In cases of no response to O

or strong drift, check the tubing for loose connections, blockages and

leaks.

CAUTION

Never apply overpressure to the O

measuring unit as the pressure transducer may

be permanently damaged.

If the message ‘O

zero error’ is displayed check the O

measuring unit output voltage on Gas

mother board (see Section Offset adjustment).
If the adjustment range of the (software) calibration is insufficient check the O

measuring unit

output voltage and adjust the gain if necessary (see Section Gain adjustment).
If there are problems with O

response time check the O

measurement flow rate and adjust it if

necessary (see Section Gas Sampling System Adjustments).
If the O

signal is noisy, check the measurement unit suspension. Frequency adjustment may help

in some cases (see Section Frequency adjustment).

4.4

ACX troubleshooting

CAUTION

The measuring unit ACX-200 can be repaired and calibrated only at the factory.

The ACX troubleshooting is carried out in the General Troubleshooting scheme. The ACX testing is

explained at the ACX service information section, please refer to it.

4.4.1

Cleaning the measuring chamber of ACX measuring unit

In case the N

O “zero calibration constant” in Gas Service (ULT) or N

O “calib zero” in ACX Service

(AM/CCM) indicates contamination of the measuring chamber (value 61000 or more), or if the

software will stuck to the “calibrating gas sensor” state due to contamination, it is possible to

attempt the measuring chamber cleaning. However, Datex-Ohmeda recommend exchanging the

measuring unit rather than cleaning.
The measuring chamber should first try to be cleaned by rinsing it with distilled water only. If rinsing

alone is not sufficient the cleaning can be tried with Datex-Ohmeda Cleaning Fluid (85969).
NOTE: Do not use other cleaning agents such as blood gas electrode cleaners. These may damage

the unit.

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Похожие инструкции для S/5 B-GAS

Бренды по названию

Популярные бренды