Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 52

Страница: 52 / 83

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

OUT

REF

FREQUENCY

GAIN

TEMP.COMP.

ZERO

Vibration insulation

Gas connectors

Figure 17

measuring unit adjustments

3.4.4

Flow calibration

PVX board is calibrated at the factory and due to the board’s design calibration is not regularly

needed. The calibration data is saved into the board’s EEPROM memory and if the software EPROM

of the board is changed the calibration must be performed. It is recommended to perform the

calibration both with adult values using the D-lite, and with pediatric values using Pedi-lite.
1.

Connect a spirometry tube with the D-lite sensor to the airway module. To improve the

accuracy, the endotracheal tube and all accessories which are in normally use should be

attached also during the calibration.

Enter service menu (Monitor Setup/Install Service/Service View/Modules).

Enter the PVX menu. After the flow is zeroed ('Zero OK' message displayed) attach

calibration pump or spirometry tester to the flow sensor (D-lite or Pedi-lite). Select the

sensor type.

Set the calibration volume for adult to 1000 ml and for pediatric to 300 ml.

Work on the calibration pump slowly, approximately 1 pump in 5 seconds, pump until

'adjust'-message appears. If you use the spirometry tester, perform the calibration

according to the tester instructions.

Adjust the reading to match the calibration volume (1000 ml for the D-lite and 300 ml for

the Pedi-lite).

Содержание S/5 B-GAS




















































































Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Бренды по названию

Популярные бренды

Datex-Ohmeda S/5 B-GAS, Техническое справочное руководство

Результаты поиска

Содержание S/5 B-GAS

Отзывы:

Бренды по названию

Популярные бренды